NIARMADA Nissan Armada manuals & owner information
Nissan Armada owner resource

Manuals, service information and practical owner guidance.

Fast access to Nissan Armada manuals, operating instructions, maintenance references and technical information.

Browse manuals →
Nissan Armada manual library

Nissan Armada 2025-2026 Service and Repair Manual: Tire Pressure Sensor

Nissan Armada 2025-2026 Service and Repair Manual / Suspension / Road Wheels & Tires / Tire Pressure Sensor

Exploded View

Screw Tire pressure sensor Valve
Valve core Valve cap
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Parts that are replaced as a set when the tire is replaced.

Removal & Installation

WARNING:

  • Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.

REMOVAL

Remove tire assembly. Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove valve cap, valve core and then deflate tire.

NOTE:

If the tire is reused, apply a matching mark to the position of the tire road wheel valve hole for the purpose of wheel balance adjustment after installation.

Use the tire changer and disengage the tire beads.

CAUTION:

Be sure not to damage the road wheel or tire pressure sensor.

Apply bead cream or an equivalent to the tire beads.

Turn tire so that valve hole is at bottom and bounce so that tire pressure sensor is near valve hole. Carefully lift tire onto turntable and position valve hole (and tire pressure sensor) 270° from mounting/dismounting head .

CAUTION:

Be sure not to damage the road wheel and tire pressure sensor.

Remove mounting screw , and then remove tire pressure sensor from valve .

Cut the part of valve, using a pliers cutters (B).

CAUTION:

Be sure not to damage the road wheel.

Remove the valve from road wheel , using a valve inserter (A).

CAUTION:

  • Be sure not to damage the road wheel.

  • Pull the valve straight through the rim hole perpendicularly to the rim hole.

INSTALLATION

CAUTION:

Never loosen the mounting screw if the tire pressure sensor and valve are assembled and spplied.

When reusing the tire pressure sensor, install the valve to the tire pressure sensor, follow the procedure below.Insert the tire pressure sensor to the roll pin of valve .

CAUTION:

Never reuse valve.

Install mounting screw .

CAUTION:

Never reuse mounting screw.

Apply a suitable non-silicone lubricant to the surface of the valve that touches (A) the wheel and to the valve hole in the wheel.

CAUTION:

  • Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.

  • Do not allow lubricant to contact the tire pressure sensor .

Install the tire pressure sensor assembly, follow the procedure below.Set the tire pressure sensor assembly to road wheel.

CAUTION:

Check the tire pressure sensor assembly direction, tire pressure sensor assembly must be inserted to the rim of road wheel as shown figure.

 Install the tire pressure sensor assembly to road wheel , using a valve inserter (A).

CAUTION:

  • Be sure not to damage the road wheel.

  • Pull the valve straight through the rim hole perpendicularly to the rim hole.

  • Avoid any contact of the tire pressure sensor with the rim well and valve with the rim hole counter bore during insertion.

  • Insert tire pressure sensor assembly all the way to the road wheel.

  • Check that tire pressure sensor assembly contacts horizontally with road wheel.

  • Check the tire pressure sensor assembly direction, tire pressure sensor assembly must be inserted to the rim of road wheel as shown figure.

  • If the position is not correct, rotate the tire pressure sensor assembly to the correct position, using a valve inserter.

Apply bead cream or an equivalent to the tire beads.

Install the tire inside beads onto the road wheel in the position shown in the figure.

Set the tire onto the turntable so that the tire changer arm is at a position approximately 270° from the tire pressure sensor .

CAUTION:

Be sure that the arm does not contact the tire pressure sensor.

Install the tire outer side beads onto the road wheel.

CAUTION:

When installing, check that the tire does not turn together with the road wheel.

Check the tire pressure for all wheels and adjust to the specified value. Refer to TIRE AIR PRESSURE : Service Data.

NOTE:

Before adding air, align the tire with the position of the matching mark applied at the time of removal.

Install tire to the vehicle. Refer to ROAD WHEEL TIRE : Removal & Installation.

Perform "TIRE PRESSURE SENSOR ID REGISTRATION" when tire pressure sensor is removed and installed, or replaced. Refer to Work Procedure.

    Other materials

    Meters and gauges
    Basic information Example The instrument cluster in the Nissan Armada is designed to provide clear, real-time information about vehicle performance and status. It combines modern digital displays with traditional gauges to ensure the driver can monitor all critical systems efficiently. ...

    Front Wiper Blade
    Removal and Installation CAUTION: Clean windshield glass and front wiper refill so that windshield glass may not be damaged by dust, etc. REMOVALOperate front wiper to the auto stop position. Refer to System Description. Lift up front wiper arm, and then lock back front wiper arm. Slide to remove fr ...

    General Maintenance
    General Maintenance General maintenance includes those items which should be checked during the normal day-to-day operation of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform checks and inspections themselves or have their INFINITI retailers d ...