Nissan Armada 2025-2026 Service and Repair Manual: Off Road Models

Exploded View

	Front bumper side bracket RH		Front bumper side retainer RH		Front bumper retainer upper
	Front bumper side stay RH		Front bumper reinforcement		Front bumper energy absorber A
	Front bumper energy absorber B RH		Front bumper energy absorber C RH		Front bumper energy absorber D
	Front bumper energy absorber C LH		Front bumper finisher		Front bumper fascia
	U nut		Front bumper side bracket LH		Front bumper side retainer LH
	Front bumper side stay LH		Front bumper energy absorber B LH		Front bumper side finisher RH
	License plate bracket		Front bumper side finisher LH		Front bumper protector (if equipped)
	Double-sided tape [t: 0.8 mm (0.031 in)] (if equipped)		Double-sided tape [t: 1.2 mm (0.047 in)] (if equipped)		Retainer (if equipped)
	Grommet (if equipped)
	Clip
	: Clip
	: Pawl
	: Always replace after every disassembly.
, , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.

Removal and Installation

WARNING:

CAUTION:

Front bumper fascia assembly is made of resin. Never apply excessive force to it, and be careful to prevent contact with oil.

REMOVAL

Remove front grille. Refer to Removal and Installation.

Remove fillet molding (with fillet molding). Refer to Removal and Installation.

Remove front bumper energy absorber A.

Disengage active grille shutter fixing clips .

Disengage fixing clips and pawls, and then remove front bumper side finisher (LH and RH).

	: Clip
	: Pawl

Remove front bumper fascia fixing clips .

Remove fixing bolts .

Remove fixing bolts .

Remove fixing screws .

Apply protective tapes (A) on the part to protect it from damage.

Pull front bumper fascia assembly side toward the vehicle side to disengage the fitting of front bumper side bracket and front bumper fascia assembly side according to the numerical order 1→2 as shown by the arrows in the figure.

: Pawl

CAUTION:

When disengage front bumper fascia assembly, 2 workers are required so as to prevent it from dropping.

Disconnect front sonar sensor harness connector.

Remove front bumper fascia assembly.

CAUTION:

When removing front bumper fascia assembly, 2 workers are required so as to prevent it from dropping.

Remove the following parts after removing front bumper fascia assembly.

• Front sonar sensor. Refer to SONAR SENSOR (FRONT) : Removal & Installation.

• License plate bracket

• Front bumper protector (if equipped)

• U nuts

• Front bumper finisher

• Grommets (if equipped)

Remove mounting nuts, and then remove front bumper retainer upper.

Remove mounting bolts, and then remove front bumper side retainer (LH and RH).

Remove active grille shutter fixing clip and mounting nuts. Refer to Exploded View.

Remove mounting nuts, and then remove front bumper reinforcement.

Remove mounting bolts, and then remove front bumper side stay (LH and RH).

Remove front bumper energy absorber B (LH and RH).

Remove front bumper energy absorber C (LH and RH).

Disengage fixing pawls, and then remove front bumper energy absorber D.

Remove front bumper side bracket (LH and RH) fixing screws.

Disengage fixing pawls, and then remove front bumper side bracket (LH and RH).

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Always replace front bumper energy absorber A with a new one.

• Always replace double-sided tapes with new ones, if front bumper protector is reused (if equipped).

• If the retainer is removed from the front bumper protector, replace the double-sided tapes with new ones (if equipped).

• Remove double-sided tapes remaining on front bumper fascia and back of front bumper protector with double-sided tape remover, after removing front bumper protector (if equipped).

• Degrease front bumper fascia mounting surface of front bumper protector, before apply primer (if equipped).

• Press-fit the entire area of the double-sided tape with 49 N (5 kg) or more of pressure after applying license plate bracket and front bumper protector on the front bumper protector (if equipped).

• Apply the double-sided tapes to the license plate bracket and front bumper protector so that it do not protrude beyond the marking line (if equipped).

• Never wash the vehicle within 24 hours after installing so as to keep adhesive.

NOTE:

• The following table shows the specified values for checking normal installation status.

• Fitting adjustment cannot be performed.

  

  Portion		Clearance	Surface height difference
  Front bumper fascia assembly – Front grille	–	0.5 - 3.5 mm (0.020 - 0.138 in)	—
  	–	0.5 - 3.5 mm (0.020 - 0.138 in)	—
  Front bumper fascia assembly – Front bumper side finisher	–	0.1 - 1.9 mm (0.004 - 0.075 in)	0.1 - 1.9 mm (0.004 - 0.075 in)
  Front bumper fascia assembly – Front combination lamp	–	1.6 - 4.2 mm (0.063 - 0.165 in)	—
  Front bumper fascia assembly – Front fender assembly	–	0.1 - 0.9 mm (0.004 - 0.035 in)	(–0.5) – (+1.5) mm [(–0.020) – (+0.059) in]

• If front bumper fascia is replaced with new one, make holes for license plate bracket installation in front bumper fascia with a drill as shown in the figure.

  • Without front bumper protector models

    1. Hold the license plate bracket to the front bumper fascia and mark two locations .

       

    2. Remove the license plate bracket and drill two square holes in the locations marks in the previous step.

       

       B

       : 26.0 mm (1.02 in)

       C

       : 19.0 mm (0.75 in)

       D

       : 71.5 mm (2.81 in)

    3. Install u nuts.

    4. Install grommets.

    5. Make holes for license plate bracket installation in front bumper fascia with a drill as shown in the figure.

       

       	Front bumper fascia
       	vehicle center		License plate bracket installation hole		R end

       Dimension
       D: Distance from vehicle center	: 64.0 mm (2.520 in)
       E: Distance from vehicle center	: 130.0 mm (5.118 in)
       F: Distance from R end of front bumper fascia	: 59.3 mm (2.335 in)
       G: Hole size	: φ 9.0 mm (0.354 in)
       H: Distance from R end of front bumper fascia	: 15.7 mm (0.618 in)

    6. Install license plate bracket with screws at the license plate bracket installation holes.

  • With front bumper protector models

    1. Hold the license plate bracket to the front bumper fascia and mark two locations .

       

    2. Remove the license plate bracket and drill two square holes in the locations marks in the previous step.

       

       B

       : 26.0 mm (1.02 in)

       C

       : 19.0 mm (0.75 in)

       D

       : 71.5 mm (2.81 in)

    3. Install license plate bracket with screws at the license plate bracket installation hole position marks .