Nissan Armada 2025-2026 Service and Repair Manual: Rear Propeller Shaft

Exploded View

REMOVAL

Propeller shaft assembly

: vehicle front

: N·m (kg-m, ft-lb)

: Always replace after every disassembly.

DISASSEMBLY

	Snap ring		Journal bearing		Journal
	Sleeve yoke		Propeller shaft tube		Flange yoke

: vehicle front

: Always replace after every disassembly.

: Select with proper thickness.

: Apply multi-purpose grease.

NOTE:

Replace , and as a set.

Removal and Installation

WARNING:

• Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.

REMOVAL

Shift the transmission to the neutral position, and then release the parking brake.

Put matching mark on rear propeller shaft flange yoke and final drive companion flange.

CAUTION:

For matching mark, use paint. Never damage propeller shaft flange and final drive companion flange.

Remove propeller shaft assembly fixing bolts and nuts.

Remove propeller shaft assembly from vehicle.

CAUTION:

Never damage rear oil seal of transfer.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

• For non-reusable parts, refer to Exploded View.

• For each tightening torque, refer to Exploded View.

• Never damage the rear oil seal lip when install rear propeller shaft to transfer.

• Align matching marks to install propeller shaft flange yoke and final drive companion flange.

  

• If propeller shaft assembly or final drive assembly has been replaced, connect them as follows:

  • Install propeller shaft while aligning matching mark of propeller shaft with matching mark of final drive on the joint as close as possible.

    

    NOTE:

    Matching mark is has been painted in either position.

• Perform inspection after installation. Refer to Inspection.

Disassembly and Assembly

DISASSEMBLY

Put a matching mark between propeller shaft and flange yoke as shown.

CAUTION:

For matching mark, use paint. Never damage the surface.

Remove snap rings .

Lightly tap bottom of yoke using a copper hammer and remove journal bearing.

CAUTION:

Never damage the yoke.

ASSEMBLY

Install journal bearing to journal.

CAUTION:

• Never reuse journal and journal bearing.

• Always replace journal, journal bearing, and snap rings as a set.

• Apply multi-purpose grease to journal bearing.

• Install bearing using a vise.

  

  CAUTION:

  Never damage bearing or flange yoke.

Measure journal axial play. If necessary, select the appropriate snap ring.While pushing to 98 N·m (10 kg-m, 72 ft-lb), check the clearance between snap ring and needle bearing .

Journal axial play

: Refer to Journal.

If journal axial play is outside the specification, use a thicker/thinner snap ring to adjust.

CAUTION:

• Never reuse snap ring.

• Select snap rings with a difference in thickness at both sides within 0.02 mm (0.0008 in). For selecting snap ring, refer to the latest parts information.

Install snap rings .

Check that the journal moves smoothly and is below the joint flex torque specification.

Joint flex torque

: Refer to Journal.

NOTE:

The joint flex torque may not be satisfied soon after the assembly.

Check the journal axial play. Refer to Inspection.

Inspection

INSPECTION AFTER REMOVAL

Appearance

Check propeller shaft tube surface for dents or cracks. If malfunction is detected, replace propeller shaft assembly.

Propeller Shaft Runout

Check propeller shaft runout at several points with a dial indicator. If runout exceeds specifications, replace propeller shaft assembly.

Propeller shaft runout

: Refer to Propeller Shaft Tube.

Journal Axial Play

As shown in the figure, while fixing yoke on one side, check axial play of joint. If the journal axial play exceeds the specification, repair or replace the journal parts.

Journal axial play

: Refer to Journal.

Joint Flex Torque

Check that the journal moves smoothly and is below the joint flex torque specification. If the joint flex torque exceeds the specification, repair or replace the journal parts.

Joint flex torque

: Refer to Journal.

INSPECTION AFTER INSTALLATION