Exploded View
 |
Transmission housing |  |
Starter motor cover 1 |  |
Starter motor cover 2 |
 |
“B” terminal harness |  |
Starter motor harness connector |  |
Starter motor |
| : vehicle front | |||||
 |
: N·m (kg-m, in-lb) | ||||
 |
: N·m (kg-m, ft-lb) | ||||
 : Indicates that the part is connected at points with same symbol in actual vehicle. |
|||||
Removal and Installation
WARNING:
REMOVAL
Disconnect battery cable from negative terminal. Refer to Removal and Installation.
Remove engine under cover rear. Refer to Removal and Installation.
Remove front cross member. Refer to Removal and Installation.
Remove starter motor cover 2 mounting bolts 
, and then remove starter motor cover 2.
| : vehicle front |
Remove starter motor cover 1 mounting bolt , and then remove starter motor cover 1.
| : vehicle front |
Remove "B" terminal harness mounting nut , and then disconnect "B" terminal harness .
| : vehicle front |
Disconnect starter motor harness connector .
| : vehicle front |
Remove starter motor upper side mounting bolt .
| : vehicle front |
Remove starter motor lower side mounting bolt .
| : vehicle front |
Remove starter motor from vehicle.
CAUTION:
Never damage around the parts.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Be careful to tighten “B” terminal harness mounting nut to the specified torque. Refer to Exploded View.
Inspection
MAGNETIC SWITCH
Remove starter motor from vehicle. Refer to Removal and Installation.
Connect 12V battery to starter motor as shown in the figure. Check that pinion gear is driven out by magnetic switch.
-
Replace starter motor if pinion gear is not driven out.
Disconnect “M” terminal as shown in the figure. Check that pinion gear does not return to original position.
-
Replace starter motor if pinion gear returns.
Disconnect (-) wire from starter motor body as shown in the figure. Check that pinion gear returns to original position.
-
Replace starter motor if pinion gear does not return.
PINION PROTRUSION LENGTH
With pinion gear driven out by magnetic switch, push pinion gear back to remove slack and measure the clearance “L” between the front edge of the pinion gear and the pinion stopper .
-
Replace starter motor if the measurement value is not within specifications.
| Clearance “L” | : Refer to Starter Motor. |
PINION CLUTCH
Check pinion gear teeth.
-
Replace starter motor if teeth are worn or damaged. (Also check condition of ring gear teeth.)
Check to see if pinion locks in one direction and rotates smoothly in the opposite direction.
-
Replace starter motor if pinion is locked, rotates in both directions or unusual resistance is evident.
NO-LOAD TEST
Remove starter motor from vehicle. Refer to Removal and Installation.
Connect 12V battery and ammeter to starter motor as shown in the figure. Check no load current with pinion gear driven out and starter motor operating.
-
Replace starter motor if the measurement value is not within specifications
| No-load current | : Refer to Starter Motor. |
Other materials
Brake assist
Brake assist
The Brake Assist system in the Nissan Armada is designed to enhance braking performance
during emergency situations. When the system detects that the driver is applying
the brake pedal with significant force, it automatically increases braking pressure
beyond what a conventional ...
Diagnosis and Repair Work Flow
Work Flow
DETAILED FLOWINTERVIEW FROM THE CUSTOMER
CAUTION:
Customers are not professional. Never guess easily like “maybe the customer means that...,” or “ maybe the customer mentions this symptom”.
>>
GO TO 2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, ...
Rear Center Console Assembly
Exploded View
REMOVAL
Rear center tray cup holder mat
Rear center tray front mask
Rear center tray assembly
Rear center tray rear mask
Rear center pocket mat
: Pawl
DISASSEMBLY
Rear center tray assembly
Rear center tray reinforcement
Removal and ...