Exploded View
12V SUB BATTERY (LITHIUM ION BATTERY) HARNESS
 |
12V sub battery (lithium ion battery) harness 1 | ||||
 |
: To 12V sub battery (lithium ion battery) | ||||
| : vehicle front | |||||
 |
: N·m (kg-m, in-lb) | ||||
 |
: N·m (kg-m, ft-lb) | ||||
12V SUB BATTERY (LITHIUM ION BATTERY)
|
:12V sub battery (lithium ion battery) cover seal |  |
:12V sub battery (lithium ion battery) cover |  |
:12V sub battery (lithium ion battery) negative cable |
 |
:12V sub battery (lithium ion battery) positive cable 2 |  |
:12V sub battery (lithium ion battery) positive cable 1 |  |
:12V sub battery (lithium ion battery) |
 |
:12V sub battery (lithium ion battery) bracket |  |
:12V sub battery (lithium ion battery) case seal |  |
:12V sub battery (lithium ion battery) case |
 |
:Oneway valve | ||||
|
:To power network separate relay | ||||
 |
:To engine room | ||||
| : vehicle front | |||||
|
: N·m (kg-m, in-lb) | ||||
|
: N·m (kg-m, ft-lb) | ||||
 |
: Always replace after every disassembly. | ||||
Removal and Installation
WARNING:
Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.
REMOVAL
Disconnect 12V battery cable from negative terminal. Refer to Precautions for Removing Battery Terminal.
CAUTION:
To prevent damage to the parts, disconnect 12V battery cable from negative terminal first.
Remove 3rd seat. Refer to Removal and Installation.
Flip the rear floor carpet to secure work space.
Remove floor cover mounting bolts , and then remove floor cover.
| : vehicle front |
Disconnect 12V sub battery (lithium ion battery) harness connector .
| : vehicle front |
Remove mounting nut , and then disconnect 12V sub battery (lithium ion battery) negative cable from negative terminal.
| : vehicle front |
Disengage fixing pawl, and then remove positive terminal cover part of 12V sub battery (lithium ion battery) in the direction of the arrow (
).
 |
: Pawl |
| : vehicle front |
Remove mounting nut , and then disconnect 12V sub battery (lithium ion battery) cable 2 from positive terminal.
| : vehicle front |
Remove mounting nuts , and then remove 12V sub battery (lithium ion battery) bracket.
| : vehicle front |
Remove 12V sub battery (lithium ion battery).
If necessary, remove the 12V sub battery (lithium ion battery) case and cover by following the steps below.Remove power network separate relay. Refer to Exploded View . Remove 12V sub battery (lithium ion battery) positive cable 1 mounting nut , harness clip and disconnect harness connectors 
| : vehicle front |
, and then move 12V sub battery (lithium ion battery) positive cable 1 from 12V sub battery (lithium ion battery) case .
| : vehicle front |
harness clip and then remove 12V sub battery (lithium ion battery) positive cable 2 from 12V sub battery (lithium ion battery) case.
 |
: Clip |
| : vehicle front |
mounting bolts and clip .
|
: Clip |
| : vehicle front |
clips from 12V sub battery (lithium ion battery) case.
|
: Clip |
| : vehicle front |
, and then remove 12V sub battery (lithium ion battery) negative cable from 12V sub battery (lithium ion battery) case .
| : vehicle front |
mounting bolt to secure work space.
case and cover mounting nuts , and then remove 12V sub battery (lithium ion battery) case and cover from vehicle.
mounting nuts , and then remove 12V sub battery (lithium ion battery) cover from 12V sub battery (lithium ion battery) case.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
-
When connecting, connect battery cable to positive terminal first.
-
Never reuse battery cover upper seal and battery case lower seal.
-
When install 12V sub battery (lithium ion battery) cover seal
, make sure that the dimensions of (A) are 20 – 40 mm (0.79 – 1.57 in).: vehicle front 
-
When install the 12V sub battery (lithium ion battery) cover
to the 12V sub battery (lithium ion battery) case, tighten the mounting nuts to the specified torque in the order of 1 ⇒ 2, then tighten the other mounting nuts to the specified torque.: vehicle front 
-
When install the 12V sub battery (lithium ion battery) cover and 12V sub battery (lithium ion battery) case
to the vehicle, tighten the mounting nuts to the specified torque in the order of 1 ⇒ 2, then tighten the other mounting nuts to the specified torque.: vehicle front 
Other materials
Diagnosis and Repair Work Flow
Work Flow
OBTAIN INFORMATION ABOUT SYMPTOM
Refer to Diagnostic Work Sheet and interview the customer to obtain the malfunction information (conditions and environment when the malfunction occurred) as much as possible when the customer brings in the vehicle.
>>
GO TO 2.
CHECK DTC
Before ch ...
Third Seat Belt Retractor
Removal and Installation
REMOVALSeat Belt Retractor (LH and RH)Remove third seat assembly. Refer to Removal and Installation.
Remove anchor plate mounting anchor bolt .
Remove shoulder anchor.Remove back pillar garnish. Refer to Removal and Installation. Remove shoulder anchor mounting anchor bolt ...
Front Wiper Blade
Removal and Installation
CAUTION:
Clean windshield glass and front wiper refill so that windshield glass may not be damaged by dust, etc. REMOVALOperate front wiper to the auto stop position. Refer to System Description.
Lift up front wiper arm, and then lock back front wiper arm.
Slide to remove fr ...