The Nissan Armada should normally be driven with the Vehicle Dynamic Control (VDC) system activated, as it plays a critical role in maintaining stability, traction, and overall vehicle control in a wide range of driving conditions.
However, in certain situations—such as when the Nissan Armada becomes stuck in mud, deep snow, or loose terrain—the VDC system may limit engine output to reduce wheel spin. In these cases, even if the accelerator pedal is fully pressed, engine power may be reduced. If maximum engine power is required to free the Nissan Armada, temporarily turning off the VDC system may help regain traction.

To deactivate the Vehicle Dynamic Control (VDC) system in the Nissan Armada, press the VDC OFF switch.
Once the system is turned off, the VDC OFF indicator light will illuminate on the instrument panel, confirming that stability control functions are disabled.
To restore normal operation, press the VDC OFF switch again or restart the Nissan Armada engine. The system will automatically reactivate to ensure optimal safety.
Brake Force Distribution
During cornering, the Nissan Armada Brake Force Distribution system intelligently adjusts braking force between all four wheels based on steering angle and turning radius. This helps maintain stability and improves control when braking through curves.
This feature enhances the overall braking balance of the Nissan Armada, especially during dynamic driving situations, contributing to safer handling and reduced risk of skidding.
WARNING
- The Nissan Armada VDC system is designed to assist in maintaining vehicle
stability but cannot prevent accidents caused by aggressive steering, excessive
speed, or unsafe driving behavior.
Always reduce speed and drive with caution, especially when cornering or driving on wet, icy, or uneven road surfaces.
- Do not modify the suspension components of the Nissan Armada. Using non-approved
or worn parts such as shocks, struts, springs, stabilizer bars, bushings, or
wheels may negatively impact VDC performance.
In such cases, the warning indicator
may flash, or both the
and
indicator lights may illuminate. - If brake components such as pads, rotors, or calipers are not NISSAN
recommended or are excessively worn, the Nissan Armada VDC system may not function
correctly, and both the
and
indicator lights may illuminate. - If engine control components are not properly maintained or do not meet
manufacturer standards, both the
and
indicator lights may illuminate, indicating reduced system performance. - When driving the Nissan Armada on steeply banked roads or extreme inclines,
the VDC system may not function as expected, and the
indicator may flash or both the
and
indicators may illuminate.
Avoid operating the Nissan Armada in such conditions whenever possible.
- Driving on unstable platforms such as ferries, ramps, elevators, or rotating
surfaces may trigger warning indicators
and
/
.This is normal behavior and not a malfunction. Restart the Nissan Armada engine after returning to stable ground.
- If non-recommended tires or wheels are installed, the Nissan Armada VDC
system may not operate properly, and warning indicators
,
and
may illuminate. - The Nissan Armada VDC system does not replace the need for proper winter tires or tire chains when driving on snow-covered or icy roads.
Other materials
Electric Power Steering Warning Lamp Does Not Turn on
Description
The power steering warning lamp does not illuminate when the ignition switch is ON (lamp check).
Diagnosis Procedure
CHECK THE POWER STEERING WARNING LAMP
Perform trouble diagnosis for the power steering warning lamp system. Refer to Component Function Check.
Is the inspection result nor ...
Seat Belt Warning Lamp Does Not Turn on
Diagnosis Procedure
CHECK DTC OF AIR BAG DIAGNOSIS SENSOR UNIT
Check DTC in “Self Diagnosis Result� mode of “AIR BAG� using CONSULT.
Is DTC detected?
YES>>
Perform trouble diagnosis related to the detected DTC. Refer to DTC Index.
NO>>
GO TO 2.
CHECK DTC OF BCM
Check DTC in “ ...
Back Door Window Glass
Exploded View
Back door outer panel
Back door window glass
Spacer A
Clip upper RH
Clip lower
Spacer B
Spacer C
Back door window glass molding
Dam sealant rubber
Clip upper LH
Glass primer
Adhesive
Adhesive mark
: Always replace after every disassembly.
...