Nissan Armada 2025-2026 Service and Repair Manual: Second Seat Belt Retractor

Removal and Installation

WARNING:

• Before servicing, disconnect ground line of battery. Refer to Precautions for Removing Battery Terminal.

• Prevent accidental activation. Refer to Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER".

REMOVAL

Seat Belt Pre-tensioner Retractor (LH and RH)

Slide second seat to front most position.

Remove anchor plate mounting anchor bolt .

Remove shoulder anchor.Remove rear pillar finisher. Refer to Removal and Installation. Remove shoulder anchor mounting anchor bolt , and then remove shoulder anchor.

Disconnect seat belt pre-tensioner retractor harness connector .

CAUTION:

Never damage harness connector.

NOTE:

Insert remover tool (A) wrapped in tape between connector and lever , and then disconnect harness connector while moving the lever.

Remove seat belt pre-tensioner retractor mounting anchor bolt and bolt , and then remove seat belt pre-tensioner retractor.

CAUTION:

Never place seat belt pre-tensioner retractor in an area where the temperature reaches 80°C (176°F) or more.

Center Seat Belt Retractor

Disengage seat cushion trim fixing retainers. Refer to Disassembly and Assembly.

Remove center anchor plate mounting anchor bolt .

Remove seatback trim and pad as a set. Refer to Disassembly and Assembly.

Remove center seat belt retractor mounting anchor nut , and then remove center seat belt retractor.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

When connect harness connector, press harness connector until the clicking sound.

Inspection

AFTER A COLLISION

WARNING:

To avoid the risk of death or severe injury:

Replace any seat belt assembly (including anchor bolts) if:

• The seat belt is in use at the time of a collision (except for minor collisions and the belts, retractors and buckles show no damage and continue to operate properly).

• The seat belt is damaged in an accident (i.e. torn webbing, bent retractor or guide, etc.).

• The seat belt attaching point is damaged in an accident. Inspect the seat belt attaching area for damage or distortion and repair if necessary before installing a new seat belt assembly.

• Anchor bolts are deformed or worn out.

• The seat belt assembly must be replaced even if the seat belts were not in use during the collision in which the air bags were deployed.

PRELIMINARY CHECKS

Check the seat belt warning lamp for proper operation. Refer to Seat Belt Warning Lamp.

If the air bag warning lamp turns ON, perform self-diagnosis using CONSULT. Refer to CONSULT Function.

Check that the seat belt retractor, seat belt anchor and buckle bolts are tightened firmly.

Check the shoulder seat belt guide for second seat. Check that guide swivels freely and that webbing lays flat and does not bind in guide.

Check retractor operation:Fully extend the seat belt webbing and check for twists, tears or other damage. Allow the seat belt to retract. Check that webbing returns smoothly and completely into the retractor. If the seat belt does not return smoothly, wipe the inside of the loops with a clean paper cloth. Dirt build-up in the loops of that upper anchors can cause the seat belts to retract slowly. Fasten the seat belt. Check that the seat belt is securely fastened. Release the seat belt. Check that the webbing and tongue return to their original position.

Repeat steps above if necessary to check the other seat belts.

SEAT BELT RETRACTOR ON-VEHICLE CHECK

Emergency Locking Retractors (ELR)

NOTE:

All seat belt retractors are Emergency Locking Retractors (ELR) type. In an emergency (sudden stop) the retractor will lock and prevent the webbing from extending any further.

Check the seat belt retractors with the following test(s) to determine if a retractor assembly is operating properly.

ELR Function Stationary Check

Grasp the shoulder webbing and pull forward quickly. The retractor should lock and prevent the belt from extending further.

ELR Function Moving Check

WARNING:

Fasten the seat belt. Buckle a passenger into the seat for the belt that is to be tested.

Proceed to the designated safe area.

Drive the vehicle at approximately 16 km/h (10 MPH). Notify any passengers of a pending sudden stop and the driver and passenger must be prepared to brace themselves in the event that the retractor does not lock. Apply brakes firmly and make a very hard stop.

During stopping, seat belts should lock and not be extended. If the seat belt retractor assembly does not lock, perform the retractor off-vehicle check.

SEAT BELT RETRACTOR OFF-VEHICLE CHECK

Seat Belt Retractor (LH and RH)

Remove second seat belt retractor assembly. Refer to Removal and Installation.

Slowly pull out webbing while tilting the retractor assembly forward from the mounted position without twisting the retractor assembly as shown in the figure.

• The webbing can be pulled out when the angle (A) is 12 degrees or less.

  

• The webbing cannot be pulled out when the angle (B) is 27 degrees or more.

  A and B	: Tilting angles
  	: vehicle front

Replace the seat belt assembly if it does not operate normally.

Center Seat Belt Retractor

Remove second seat belt retractor assembly. Refer to Removal and Installation.

Slowly pull out webbing while tilting the retractor assembly forward from the mounted position without twisting the retractor assembly as shown in the figure.

• The webbing can be pulled out when the angle (A) is 12 degrees or less.

  

• The webbing cannot be pulled out when the angle (B) is 27 degrees or more.

  A and B	: Tilting angles
  	: vehicle front

Replace the seat belt assembly if it does not operate normally.