Chevrolet Sonic manuals
 

Nissan Armada 2025-2026 Service and Repair Manual: When SRS is activated in a collision

Nissan Armada 2025-2026 Service and Repair Manual / Restraints / Srs Airbag — Basic Inspection / Collision Diagnosis / When SRS is activated in a collision

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

  1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been completed.

  2. Replace the diagnosis sensor unit.

  3. Remove the front air bag modules, knee air bag module, crash zone sensor assembly, bracket and seat belt pre-tensioner assemblies.

  4. Check the SRS components using the table below.

    Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc).

  5. Install new front air bag modules, knee air bag module, crash zone sensor assembly, bracket and seat belt pre-tensioner assemblies.

  6. Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to System Description for details.

    Ensure entire SRS operates properly.

  7. After the work is completed, check that no malfunction is detected by air bag warning lamp.

SRS INSPECTION (FOR FRONTAL COLLISION)

Part Inspection
Driver air bag module

If the driver air bag has deployed:

REPLACE

Install with new fasteners.
Driver knee air bag module

If the driver knee air bag has deployed:

REPLACE

Install with new fasteners.
Front passenger air bag module

If the front passenger air bag has deployed:

REPLACE

Install with new fasteners.
Front passenger knee air bag module

If the front passenger knee air bag has deployed:

REPLACE

Install with new fasteners.
Crash zone sensor

If any of the front air bags or seat belt pre-tensioners* have been activated:

REPLACE the crash zone sensor and bracket with new fasteners.

*: Confirm seat belt pre-tensioner activation using CONSULT only.

Seat belt pre-tensioner assemblies

(All applicable locations: buckle, retractor, lap outer)

If either the driver or passenger seat belt pre-tensioner* has been activated:

REPLACE all seat belt pre-tensioner assemblies with new fasteners.

*: Confirm seat belt pre-tensioner activation using CONSULT only.
Diagnosis sensor unit

If any of the SRS components have been activated:

REPLACE the diagnosis sensor unit.

Install with new fasteners.
Steering wheel

  1. Visually check steering wheel for deformities.

  2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.

  3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

  4. Check steering wheel for excessive free play.

  5. If no damage is found, reinstall.

  6. If damaged - REPLACE.

Spiral cable

If the driver front air bag has deployed:

REPLACE the spiral cable.
Occupant classification system (Passenger seat)

  1. Remove passenger seat assembly.

  2. Check control unit case for dents, cracks of deformities.

  3. Check connectors for damage and terminals for deformities.

  4. Check seat frame and cushion pan for dents or deformities.

  5. If no damage is found, reinstall seat with new fasteners.

  6. If damaged - REPLACE seat cushion assembly with new fasteners.

  7. Perform zero point reset function after front passenger seat is installed in the vehicle and all bolts are tightened to specification. Refer to Work Procedure.

Harness and connectors

  1. Check connectors for poor connection, damage, and terminals for deformities.

  2. Check harness for binding, chafing, cuts, or deformities.

  3. If no damage is found, reinstall the harness and connectors.

  4. If damaged - REPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness.

Instrument panel assembly

If the front passenger air bag and/or knee air bag has deployed:

REPLACE the instrument panel assembly. (integrated type)
For Frontal Collision
...

When SRS is not activated in a collision
CAUTION: WORK PROCEDURE Check the SRS components using the table below. Ensure entire SRS operates properly. SRS INSPECTION (FOR FRONTAL COLLISION) Part Inspection Driver air bag module If the dri ...

Other materials:

Fluids and Lubricants
Recommended Fluid and Lubricants The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedures described elsewhere in this manual. Fluid type Capacity (approximate) Recommended Fluids/Lubricants Metric Measure US Measure Im ...

Inspection and Repair
INSPECTION When measuring voltage, wrap tin foil around the top of the negative probe. Then press the foil against the wire with your finger. Attach probe circuit tester (in Volt range) to middle portion of each filament. If a filament is burned out, circuit tester registers 0 or battery voltage ...

Removal and Installation
REMOVAL Remove glove box lid inner. Refer to Removal and Installation. Disengage fixing pawls, and then remove filter cover. : Pawl Remove in-cabin microfilter. INSTALLATION Note the following items, and then install in the reverse order of removal. CAUTION: If the filter is deformed/damaged wh ...

© 2014-2026 Copyright www.niarmada.com
 
0.0052