NIARMADA Nissan Armada manuals & owner information
Nissan Armada owner resource

Manuals, service information and practical owner guidance.

Fast access to Nissan Armada manuals, operating instructions, maintenance references and technical information.

Browse manuals →
Nissan Armada manual library

Nissan Armada 2025-2026 Service and Repair Manual: Additional Service When Replacing Control Valve & Tcm

Nissan Armada 2025-2026 Service and Repair Manual / Transmission & Driveline / Transaxle & Transmission. 9at: Ge9r01a / Additional Service When Replacing Control Valve & Tcm

Description

WARNING:

  • Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.

When replacing the control valve & TCM, perform the following work. For work procedure, refer to Work Procedure.

  • A/T fluid filling

  • Calibration of park position sensor

  • vehicle specifications writing

    CAUTION:

    Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.

  • A/T fluid level adjustment

  • Torque converter clutch point learning

  • Calibration of decel G sensor

Work Procedure

WARNING:

  • Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.

REPLACE CONTROL VALVE & TCM

Replace control valve & TCM. Refer to Removal and Installation.

>>

GO TO 2.

REFILL A/T FLUID

Refill A/T fluid. Refer to Changing.

NOTE:

Just fill A/T fluid in this step, A/T fluid level is adjusted in the step 4.

>>

GO TO 3.

CALIBRATE PARK POSITION SENSOR AND WRITING vehicle SPECIFICATIONS

With CONSULT

  1. Ignition switch ON.

  2. Select "TRANSMISSION".

  3. Select "Replace ECU".

  4. Perform the work according to the procedure displayed in CONSULT.

CAUTION:

If the shift position is not displayed on the combination meter after writing the vehicle specifications, confirm that the shift position is displayed on the combination meter after performing one of the following actions.

  • Turn the ignition switch OFF and wait until the combination meter turns off. Then turn the ignition switch ON.

  • Disconnect the 12V battery terminal and reconnect it. Then turn the ignition switch ON. Refer to Precautions for Removing Battery Terminal.

>>

GO TO 4.

ADJUST A/T FLUID LEVEL

Adjust A/T fluid level. Refer to Adjustment.

>>

GO TO 5.

PERFORM TORQUE CONVERTER CLUTCH POINT LEARNING

Perform torque converter clutch point learning. Refer to Descripton.

>>

GO TO 6.

CALIBRATE DECEL G SENSOR

  1. Perform decel G sensor calibration. Refer to Description.

  2. Clear any DTCs that may have set and then test drive the vehicle.

>>

WORK END

    Other materials

    Condenser Inlet Pipe
    Removal and Installation REMOVALCAUTION: Perform lubricant return operation before each refrigeration system disassembly. However, if a large amount of refrigerant or lubricant leak is detected, never perform lubricant return operation. Refer to Perform Lubricant Return Operation. When disconnec ...

    Second Seatback
    Disassembly and Assembly CAUTION: When disassemble, always use a remover tool that is made of plastic to prevent damage.DISASSEMBLYRemove armrest.Disengage fixing pawls using a remover tool (A), and then remove armrest cover. : Pawl Remove mounting bolt, and then remove armrest. Remove insid ...

    Precautions
    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger fo ...