Automatic Back Door Control Unit
Diagnosis Procedure
CHECK DTC WITH AUTOMATIC BACK DOOR CONTROL UNIT
Check that DTC is not detected with automatic back door control unit.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Refer to DTC Index.
CHECK OPEN SWITCH
Check open switch.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the malfunctioning parts.
CHECK CLOSE SWITCH
Check close switch.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace the malfunctioning parts.
CHECK HALF LATCH SWITCH
Check half latch switch.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace the malfunctioning parts.
CHECK BACK DOOR CLOSURE MOTOR
Check back door closure motor.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace the malfunctioning parts.
REPLACE BACK DOOR LOCK ASSEMBLY
-
Replace back door lock assembly. Refer to Removal and Installation.
-
Confirm the operation after replacement.
Is the inspection result normal?
YES>>INSPECTION END
NO>>GO TO 7.
REPLACE AUTOMATIC BACK DOOR CONTROL UNIT
-
Replace automatic back door control unit. Refer to Removal and Installation .
-
Confirm the operation after replacement.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Check intermittent incident. Refer to Intermittent Incident.
Back Door Auto Closure Control Unit
Diagnosis Procedure
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check back door auto closure control unit power supply and ground circuit.
Refer to XXX.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunctioning parts.
CHECK DTC WITH BACK DOOR AUTO CLOSURE CONTROL UNIT
Check that DTC is not detected with back door auto closure control unit.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Refer to DTC Index.
CHECK OPEN SWITCH
Check open switch.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace the malfunctioning parts.
CHECK CLOSE SWITCH
Check close switch.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace the malfunctioning parts.
CHECK HALF LATCH SWITCH
Check half latch switch.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace the malfunctioning parts.
CHECK BACK DOOR CLOSURE MOTOR
Check back door closure motor.
Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace the malfunctioning parts.
REPLACE BACK DOOR LOCK ASSEMBLY
-
Replace back door lock assembly. Refer to Removal and Installation.
-
Confirm the operation after replacement.
Is the inspection result normal?
YES>>INSPECTION END
NO>>GO TO 8.
REPLACE BACK DOOR AUTO CLOSURE CONTROL UNIT
-
Replace back door auto closure control unit. Refer to Removal and Installation.
-
Confirm the operation after replacement.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Check intermittent incident. Refer to Intermittent Incident.
Other materials
STANDARD mode
The symbol of this Nissan Armada mode is
.
STANDARD mode is the default setting in the Nissan Armada and is optimized for
everyday driving. It provides a balanced combination of performance, comfort, and
efficiency suitable for most road conditions.
ECO mode
Basic information
The symbol of ...
Center Pillar Upper Garnish
Removal and Installation
CAUTION:
Never damage the body panel.REMOVALCAUTION:
When removing, always use a remover tool that is made of plastic to prevent damage to the parts.Remove center pillar lower garnish. Refer to Removal and Installation.
Pull out tongue of seat belt pre-tensioner retractor fr ...
Diagnosis and Repair Workflow
Around View Monitor
Work Flow
OVERALL SEQUENCE
Reference 1··· Refer to Consult Function.
Reference 2··· Refer to DTC Index.
Reference 3··· Refer to Symptom Table.
DETAILED FLOWINTERVIEW AND SYMPTOM CONFIRMATION
Check the malfunction symptoms by performing the following items.
Inte ...