Body Construction
 |
Outer side body |  |
Outer front pillar reinforcement |  |
Upper front pillar reinforcement |
 |
Upper inner front pillar |  |
Side dash reinforcement (Upper) |  |
Upper side dash |
 |
Weld nut |  |
Upper hinge plate |  |
Hoodledge reinforcement |
 |
Upper front pillar hinge brace |  |
Side dash |  |
Side dash reinforcement (Lower) |
 |
Lower dash bracket |  |
Lower dash reinforcement |  |
Lower dash |
 |
Lower front pillar reinforcement |  |
Outer sill reinforcement (Outer front) |  |
Outer sill reinforcement (Upper front) |
 |
Outer front sill reinforcement |  |
Front floor |  |
Inner gusset reinforcement |
 |
2nd body member mounting |  |
Outer gusset reinforcement |  |
2nd body bracket mounting |
 |
Inner sill reinforcement (Front) |  |
Inner sill |  |
Outer sill reinforcement (Lower front) |
 |
Inner center pillar |  |
Inner center pillar reinforcement |  |
Center pillar hinge brace |
 |
Lower hinge plate |  |
Outer sill reinforcement (Upper rear) |  |
Inner sill reinforcement (Rear) |
 |
Outer sill reinforcement (Outer rear) |  |
Outer sill reinforcement (Lower rear) |  |
Rear floor front |
 |
Inner sill extension |  |
Side step bracket |  |
Sill closing plate |
 |
Outer rear wheelhouse |  |
Inner side panel reinforcement |  |
Inner rear pillar |
 |
Back pillar main |  |
Inner back pillar |  |
Lower inner rear pillar |
 |
Back pillar reinforcement |
Fusible Insulator Applying Part
Apply the fusible insulator (melsheet) to the floor upper surface and dashboard panel interior side to block noise, vibration, and exhaust gas heat.
Unit: mm (in)
|
T=4.0 (0.157) | |
T=3.0 (0.118) | |
T=4.0 (0.157) |
|
T=4.0 (0.157) | |
T=3.0 (0.118) | |
T=3.0 (0.118) |
|
T=4.0 (0.157) | |
T=4.0 (0.157) | |
T=3.0 (0.118) |
|
T=4.0 (0.157) | |
T=4.0 (0.157) | |
T=3.0 (0.118) |
|
T=3.0 (0.118) | |
T=3.0 (0.118) | ||
|
: vehicle front  : Fusible insulator applying part |
|||||
LEFT SIDE VIEW
Unit: mm (in)
|
T=3.0 (0.118) | |
T=3.0 (0.118) | ||
|
: vehicle front : Fusible insulator applying part |
|||||
RIGHT SIDE VIEW
Unit: mm (in)
|
T=3.0 (0.118) | |
T=3.0 (0.118) | ||
|
: vehicle front : Fusible insulator applying part |
|||||
DASH PANEL
Unit: mm (in)
|
T=3.5 (0.138) | ||||
|
: vehicle front : Fusible insulator applying part |
|||||
Other materials
Idle Air Volume Learning
Description
Idle Air Volume Learning is a function of ECM to learn the idle air volume that keeps engine idle speed within the specific range. It must be performed under the following conditions:
Each time electric throttle control actuator or ECM is replaced.
Idle speed or ignition timing is out ...
Transfer Control Actuator
Exploded View
Transfer assembly
Transfer control actuator
bracket
: N·m (kg-m, in-lb)
Removal and Installation
WARNING:
Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer t ...
Additional Service When Replacing Front Camera Unit
Work Procedure
Always perform the front camera unit configuration after replacing the front camera unit.
Always perform the camera aiming after removing and installing or replacing the front camera unit.
CAUTION:
The system does not operate normally unless the front camera unit configuration an ...