Work Support
For each work support, follow the procedure shown in CONSULT.
The table below shows the additional explanations provided in the CONSULT.
CAUTION:
At the end of the work, be sure to perform a “Vehicle height adjustment” and adjust the vehicle to NORMAL height before returning it to the customer.
| Work support item | CONSULT Display | Description |
|---|---|---|
| All Items |
Operation has been stopped due to following reasons.
|
Refer to Work Flow. |
| All Items |
Timeout has expired. Refer to service manual. |
Inspect the followings:
|
| All Items |
A malfunction in the actuator is detected. Refer to service manual. |
Perform self-diagnosis of "Air suspension". (If it detects any DTC) |
|
System error is detected. Perform self-diagnosis for air suspension and check power supply system. |
||
|
A malfunction in the height sensor is detected. Perform self-diagnosis for air suspension. |
||
|
Valve is inactive. Refer to service manual. |
||
| Height sensor calibration | NG1 |
Cause:The height sensor has a narrow range of motion and the direction of rotation is wrong. Countermeasure:Confirm the status of installation. |
| Height sensor calibration | NG2 |
Cause:The height sensor has a narrow range of motion. Countermeasure:Confirm the status of installation. |
| Height sensor calibration | NG3 |
Cause:The height sensor's direction of rotation is wrong. Countermeasure:Confirm the status of installation. |
| vehicle height adjustment | Normal height |
Normal height
If the measurement is out of range, inspect the followings:
|
| vehicle height adjustment | Access height |
It decreases approximately 20 mm (0.8 in) at the front and approximately 50 mm (2.0 in) at the rear from Normal height. (For USA). It decreases approximately 70 mm (2.8 in) from Normal height. (For Canada) If the measurement is out of range, inspect the followings:
|
| vehicle height adjustment | Aero height |
It decreases approximately 20 mm (0.8 in) from Normal height. If the measurement is out of range, inspect the followings:
|
| vehicle height adjustment | High height |
It increases approximately 50 mm (2.0 in) from Normal height. If the measurement is out of range, inspect the followings:
|
| Air filling/pressure measurement | HIGH |
It displays when "air volume" is 140 bar or more. (Air volume displays total amount of air in four locations of air spring and air tank.) When it displays HIGH, release air tank's pressure to make the value of "Air tank" 7.5 ~ 12.5 bar. If it still displays HIGH, install air suspension parts again. |
| Air filling/pressure measurement | LOW |
When it displays "LOW", fill Air spring with the air and adjust the vehicle posture. Take measurements, and if it displays "LOW", refill the air tank with pressure to make the value of "Air tank" 7.5 ~ 12.5 bar.If it still displays LOW, install air suspension parts again. |
| VIN registration |
VIN MISMATCHED BETWEEN THE 1ST AND 2ND TIMES. |
VIN mismatched between the 1st and 2nd times. |
Other materials
Air Breather
Exploded View
Transfer assembly
Air breather hose A
Clip A
Hose connector
Clip B
Air breather hose B
Clip C
Air breather
: Always replace after every disassembly.
Removal and Installation
WARNING:
Jacking up or lift up the vehicle may the vehicle hei ...
Door Motor
Exploded View
FRONT
Front heater & cooling unit assembly
Front air mix door motor (driver side)
Front mode door motor
Front blower unit assembly
Intake door motor
Front air mix door motor (passenger side)
: vehicle front
REAR
Rear A/C unit assembly
Rear mode door motor ...
Driving Video Recorder Control Module
Removal and Installation
REMOVALCAUTION:
Before replacing driving video recorder control module, perform “ADDITIONAL SERVICE WHEN REPLACING DRIVING VIDEO RECORDER CONTROL MODULE”. For details, refer to Work Procedure.
Before replacing the driving video recorder control module, the customer s ...