NIARMADA Nissan Armada manuals & owner information
Nissan Armada owner resource

Manuals, service information and practical owner guidance.

Fast access to Nissan Armada manuals, operating instructions, maintenance references and technical information.

Browse manuals →
Nissan Armada manual library

Nissan Armada 2025-2026 Service and Repair Manual: Oil Pan (upper)

Nissan Armada 2025-2026 Service and Repair Manual / Engine / Engine Mechanical / Oil Pan (upper)

Exploded View

Oil pan (upper) O-ring 1 Engine oil pressure control solenoid valve
O-ring 2 Engine oil level sensor O-ring 3
Oil level gauge guide O-ring 4 Oil level gauge
Comply with the installation procedure when tightening. Refer to Disassembly and Assembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Sealing point
: Indicates that the parts is connected at points with same symbols in actual vehicle.

Disassembly and Assembly

WARNING:

  • Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.

REMOVAL

CAUTION:

Never drain engine oil when the engine is hot to avoid the danger of being scalded.

Remove main muffler. Refer to EXHAUST SYSTEM : Removal & Installation.

Remove front propeller shaft. (4WD models) Refer to Removal and Installation.

Remove rear propeller shaft. Refer to following :

  • 2WD models: Refer to Removal and Installation.

  • 4WD models with rear final drive (R240): Refer to Removal and Installation.

  • 4WD models with rear final drive [R240(DL)]: Refer to Removal and Installation.

Remove front final drive assembly. (4WD models) Refer to Removal and Installation.

Remove front stabilizer. Refer to Removal and Installation.

Remove A/T assembly. Refer to following:

  • 2WD models: Refer to Removal and Installation.

  • 4WD models: Refer to Removal and Installation.

Remove oil level gauge and oil level gauge guide.

Drain engine oil. Refer to Draining.

Remove oil filter. Refer to Removal and Installation.

Remove oil cooler.Refer to Removal and Installation.

Remove engine oil level sensor .

Remove oil pan (lower). Refer to Removal and Installation.

Remove engine oil pressure control solenoid valve .

Loosen mounting bolts in the order from 14 to 1 as shown in the figure using a power tool (commercial service tool) to remove.

: Engine front

  • Insert the seal cutter [SST: KV10111100 (NI-37228)] between oil pan (upper) and lower cylinder block. Slide seal cutter by tapping on the side of tool with a hammer. Remove oil pan (upper).

    CAUTION:

    • Never damage the mating surfaces.

    • Never insert a screwdriver, because this damages the mating surfaces.

Remove O-ring from bottom of lower cylinder block .

: Engine front

INSTALLATION

CAUTION:

Do not reuse O-rings.

Install oil pan (upper) as follows:Use a scraper (A) to remove old liquid gasket from mating surfaces.

CAUTION:

Never scratch or damage the mating surfaces when cleaning off old liquid gasket.

  • Also remove old liquid gasket from mating surface of lower cylinder block.

  • Remove old liquid gasket from the bolt holes and threads.

Install new O-ring on the bottom of lower cylinder block .

CAUTION:

Do not reuse O-rings.

: Engine front

Apply a continuous bead of liquid gasket with the tube presser (commercial service tool) to the cylinder block mating surface of oil pan (upper) to a limited portion as shown in the figure.

: φ3.4 - 4.4 mm (0.134 - 0.173 in)

Use Genuine RTV Silicone Sealant or an equivalent. Refer to Recommended Chemical Products and Sealants.

CAUTION:

  • For bolt holes with marks (6 locations), apply liquid gasket outside the holes.

  • Attaching should be done within 5 minutes after coating.

Install oil pan (upper).

CAUTION:

Never misalign both O-rings during installation.

  • Tighten mounting bolts to the torque specified below in the order from 1 to 14 as shown in the figure.

    : 17.9 N·m (1.8 kg-m, 13 ft-lb)
    : Engine front

Install oil pan (lower). Refer to Removal and Installation.

Install oil pan drain plug.

  • the figure of components on the prior page for installation direction of drain plug washer. Refer to Removal and Installation.

Install in the reverse order of removal after this step.

NOTE:

Wait at least 30 minutes after oil pan is installed before pouring engine oil.

Inspection

INSPECTION AFTER REMOVAL

Clean oil strainer if any object is attached.

INSPECTION AFTER INSTALLATION

Check the engine oil level and adjust engine oil. Refer to Inspection.

Start engine, and check there is no leakage of engine oil.

Stop engine and wait for 10 minutes.

Check the engine oil level again. Refer to Inspection.

    Other materials

    Noise, Vibration and Harshness (nvh) Troubleshooting
    NVH Troubleshooting Chart Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If necessary, repair or replace these parts. SUSPECTED PARTS (Possible cause) Symptom Reference Transfer fluid leakage Noise TRANSFER FLUID (Level low)   1 ...

    Back Door Lower Finisher
    Removal and Installation CAUTION: Never damage the back door panel.REMOVALCAUTION: When removing, always use a remover tool that is made of plastic to prevent damage to the parts.Remove back door pull handle. Refer to Removal and Installation. Remove back door finisher cap (without automatic back do ...

    Distance Sensor
    Exploded View Front bumper reinforcement Distance sensor bracket Distance sensor : N·m (kg-m, in-lb)         Removal and Installation WARNING: Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the ...