Nissan Armada 2025-2026 Service and Repair Manual: Work Procedure
CAUTION:
Make sure to use CONSULT when performing stroke sensor calibration. (It cannot be performed by any means other than CONSULT.)
VEHICLE CONDITION
Stop the vehicle.
Turn the ignition switch OFF and disconnect CONSULT from data link connector.
GO TO 2.
CHECK 12V BATTERY
Check the 12V battery. Refer to Work Flow.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Charge or replace the 12V battery. Refer toWork Flow or Removal and Installation. GO TO 3.
CHECKING INSTALLATION CONDITIONS OF BRAKE COMPONENTS
Check the installation conditions of brake components.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected parts. GO TO 4.
CHECK BRAKE PEDAL
Check the brake pedal.
- Brake pedal height: Refer to Inspection and Adjustment.
- Brake pedal assembly: Refer to Inspection.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Adjust the brake pedal height or replace brake pedal assembly.
- Adjust the brake pedal: Refer to Inspection and Adjustment.
- Replace the brake pedal: Refer to Removal and Installation.
PERFORM SELF-DIAGNOSIS
With CONSULT
Turn the ignition switch OFF to ON without depressing the brake pedal.
CAUTION:
Never start engine.
Repeat step 1 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the ignition switch OFF.
Turn the ignition switch OFF and disconnect CONSULT from data link connector.
Get out of the vehicle, close all doors, check that the room lamp is OFF, and wait for 3 minutes or more without opening these doors.
CAUTION:
Never operate the vehicle.
Turn the ignition switch ON without depressing the brake pedal.
CAUTION:
Never start engine.
Erase self-diagnosis result for “ABS”.
Turn the ignition switch OFF and disconnect CONSULT from data link connector.
CAUTION:
Never operate the vehicle.
Turn the ignition switch ON without depressing the brake pedal.
CAUTION:
Never start engine.
Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
Release brake pedal.
Perform self-diagnosis for “ABS”.
Is a malfunction detected?
YES>>Check the DTC. Refer to DTC Index. GO TO 6.
NO>>GO TO 6.
PERFORM PEDAL STROKE SENSOR CALIBRATION
With CONSULT
Turn the ignition switch OFF and disconnect CONSULT from data link connector and wait for 10 seconds or more.
Turn the ignition switch ON without depressing the brake pedal.
CAUTION:
Never start engine.
Start CONSULT and select "ABS" , "Work support" and "Stroke sensor calibration" according to this order.
CAUTION:
Never depress brake pedal.
Touch “START”.
Is either “COMPLETED” or “The operation is incomplete. Try again after confirming the operation condition.” displayed?
“COMPLETED”>>Touch the “END”. GO TO 7.
“The operation is incomplete. Try again after confirming the operation condition.”>>GO TO 1.
CHECK DATA MONITOR
With CONSULT
Select “ABS”, “Data monitor” and “Stroke sensor output voltage” according to this order. Check that this signal is within the specified value. Refer to Reference Value.
Is the inspection result normal?
YES>>GO TO 8.
NO>>GO TO 6.
ERASE SELF-DIAGNOSIS MEMORY
With CONSULT
Turn the ignition switch OFF and disconnect CONSULT from data link connector and wait for 10 seconds or more.
CAUTION:
Be sure to perform the operation above.
Turn the ignition switch ON without depressing the brake pedal.
CAUTION:
Never start engine.
Erase self-diagnosis result for “ABS”.
Turn the ignition switch OFF and disconnect CONSULT from data link connector.
CAUTION:
Never operate the vehicle.
Are the memories erased?
YES>>INSPECTION END
NO>>Check the items indicated by the self-diagnosis.
Stroke Sensor Calibration
CAUTION:
Always perform stroke sensor calibration before driving after any of the following operations is performed.
×: Necessary, -: Not necessary
Procedure Stroke sensor calibration Removing/ins ...
Adjustment of Brake Caliper Initial Position
CAUTION:
When performing the following operations, always use CONSULT (It cannot be performed by any means other than CONSULT.), for performing "Initialization position adjustment" of "Work support". ...
Other materials:
Symptom Table
Symptom Possible causeInspection itemSecond heated seat system does not operateDisplay unit and rear A/C control operation does not operateFuseSecond seat heater power supply/ground/LIN signal circuitSecond seat cushion heaterSecond seatback heaterA/C auto amp.
Check second seat heater
Refer to Comp ...
Control Units and Electrical Parts
PRECAUTIONS
Never reverse polarity of battery terminals.
Install only parts specified for a vehicle.
Before replacing the control unit, check the input and output and functions of the component parts.
Do not apply excessive force when disconnecting a connector.
Do not apply excessive shock to the c ...
Clock and outside air temperature
In the Nissan Armada, both the clock 1 and the outside air temperature 2 are
conveniently displayed at the top section of the vehicle information display, allowing
the driver to quickly access essential information while driving.
Clock
The clock in the Nissan Armada can be adjusted through ...
0.006