Body Center Marks
Factory marks exist on certain parts of the body to indicate the vehicle center. When repairing the vehicle frame (members, pillars, etc.) damaged in an accident, the most accurate and effective repair will be achieved by using these marks together with body alignment specifications.
| : vehicle front |
Unit: mm (in)
| Points | Portion | Marks |
|---|---|---|
| A | Front roof | Embossment |
| B | Upper dash | Indent |
| C | Rear roof | Indent |
Description
-
All dimensions indicated in the figures are actual.
-
When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself to make sure there is no free play.
-
When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
-
Measurements should be taken at the center of the mounting holes.
-
A star mark (
) following the value at the measuring point indicates that the measuring point on the other side is symmetrically the same value. -
The coordinates of the measurement points are the distances measured from the standard line of ″X″, ″Y″ and ″Z″.
-
″Z″: Imaginary base line [300 mm (11.81 in) below datum line (″0Z″ at design plan)]
 |
vehicle center |  |
Front axle center |  |
Imaginary base line |
Engine Compartment
WARNING:
-
Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.
MEASUREMENT
Dimensions marked with ″″ indicate symmetrically identical dimensions on both the right and left hand of the vehicle.
| Unit: mm (in) |
Unit: mm (in)
| Point | Dimension | Memo | Point | Dimension | Memo | Point | Dimension | Memo |
|---|---|---|---|---|---|---|---|---|
 –  |
833 (32.80) |
–  |
1653 (65.08) |  –  |
1688 (66.46) | |||
–  |
863 (33.98) |
 –  |
1662 (65.43) |  –  |
314 (12.36) |
|||
–  |
992 (39.06) | –  |
1482 (58.35) |
–  |
1304 (51.34) |
|||
–  |
912 (35.91) | –  |
1701 (66.97) |
–  |
473 (18.62) |
|||
| – |
987 (38.86) |
– |
598 (23.54) | –  |
782 (30.79) | |||
 – |
390 (15.35) |
– |
522 (20.55) |  – |
717 (28.23) | |||
| – |
1752 (68.98) |
– |
1535 (60.43) | – |
1308 (51.50) | |||
–  |
489 (19.25) |
– |
1588 (62.52) | – |
160 (6.30) |
|||
| – |
1579 (62.17) |
–  |
677 (26.65) |
–  |
1328 (52.28) |
|||
–  |
666 (26.22) |
– |
646 (25.43) |
– |
709 (27.91) | |||
| – |
1849 (72.80) |
–  |
1409 (55.47) |
– |
631 (24.84) | |||
| – |
934 (36.77) | –  |
1629 (64.13) | – |
709 (27.91) | |||
 – |
885 (34.84) | – |
433 (17.05) |
– |
630 (24.80) | |||
| – |
1728 (68.03) | – |
1502 (59.13) |
— | — | |||
| – |
1777 (69.96) | – |
1287 (50.67) | — | — |
MEASUREMENT POINTS
| : vehicle front |
Unit: mm (in)
| Point | Material | Point | Material |
|---|---|---|---|
|
Upper dash indent of center positioning mark | |
Upper radiator core support hole center
: φ11 (0.43) |
|
Hood hinge installing hole center φ11 (0.43) | |
Battery support front bracket hole center φ9 (0.35) |
|
Front fender installing hole center φ7 (0.28) | |
Head lamp installing hole center φ7 (0.28) |
|
Hoodledge reinforcement hole center φ12 (0.47) | |
Front bumper retainer installing hole center φ7 (0.28) |
|
Lower hoodledge hole center
: φ7 (0.28) |
|
Radiator core main support hole center φ12 (0.47) |
Underbody
WARNING:
-
Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.
MEASUREMENT (CABIN)
Bottom view
Dimensions marked with ″″ indicate symmetrically identical dimensions on both the right and left hand of the vehicle.
The following figure shows a bottom view of the vehicle.
|
Unit: mm (in) : vehicle front  : Vehicle left side |
Unit: mm (in)
| Point | Dimension | Memo | Point | Dimension | Memo | Point | Dimension | Memo |
|---|---|---|---|---|---|---|---|---|
| – |
1102 (43.39) |
– |
1253 (49.33) |
– |
1702 (67.01) |
|||
| – |
921 (36.26) |
– |
1556 (61.26) |
– |
436 (17.17) | |||
| – |
1452 (57.17) |
– |
1870 (73.62) |
– |
436 (17.17) |
Left side view
The following figure shows a side view of the vehicle.
|
Unit: mm (in) : vehicle front |
MEASUREMENT POINTS (CABIN)
| : vehicle front |
Unit: mm (in)
| Points | Coordinates | Remarks | Points | Coordinates | Remarks | ||||
|---|---|---|---|---|---|---|---|---|---|
| X | Y | Z | X | Y | Z | ||||
 |
±603.5 (±23.760) |
-555.0 (-21.850) |
407.7 (16.051) |
Hole φ21 (0.83) | |
±582.0 (±22.913) |
3150.0 (124.016) |
486.3 (19.146) |
Hole 12×8 (0.47×0.28) |
|
±672.9 (±26.492) |
612.7 (24.122) |
265.8 (10.465) |
Hole φ23 (0.91) | |
±218.0 (±8.583) |
3305.8 (130.149) |
491.5 (19.350) |
Hole 18×16 (0.71×0.63) |
|
±420.0 (±16.535) |
750.0 (29.528) |
306.2 (12.055) |
Hole 16×12 (0.63×0.47) | |
±435.0 (±17.126) |
3520.0 (138.582) |
484.4 (19.071) |
: Hole φ16 (0.63) |
|
±420.0 (±16.535) |
1600.0 (62.992) |
312.6 (12.307) |
Hole φ16 (0.63) | |
±583.0 (±22.953) |
3815.0 (150.197) |
482.3 (18.988) |
Hole 18×16 (0.71×0.63) |
|
±678.0 (±26.693) |
2440.0 (96.063) |
359.0 (14.134) |
Hole φ27 (1.06) | |
±218.0 (±8.583) |
3881.0 (152.795) |
490.0 (19.291) |
Hole 18×13 (0.71×0.51) |
|
±218.0 (±8.583) |
2650.0 (104.331) |
390.2 (15.362) |
Hole 18×16 (0.71×0.63) | |
±645.0 (±25.394) |
3980.0 (156.693) |
454.1 (17.878) |
Hole φ23 (0.91) |
MEASUREMENT (FRAME)
Bottom view
Dimensions marked with ″″ indicate symmetrically identical dimensions on both the right and left hand of the vehicle.
The following figure shows a bottom view of the vehicle.
|
Unit: mm (in) : vehicle front : Vehicle left side |
Unit: mm (in)
| Point | Dimension | Memo | Point | Dimension | Memo | Point | Dimension | Memo |
|---|---|---|---|---|---|---|---|---|
| – |
1295 (50.98) |
– |
871 (34.29) |
– |
1356 (53.39) | |||
| – |
1380 (54.33) |
– |
287 (11.30) |
– |
570 (22.44) | |||
| – |
286 (11.26) |
– |
1323 (52.09) |
– |
1290 (50.79) | |||
| – |
1159 (45.63) |
– |
1727 (67.99) | — | — | |||
| – |
207 (8.15) |
– |
1773 (69.80) | — | — |
Left side view
The following figure shows a side view of the vehicle.
|
Unit: mm (in) : vehicle front |
Front view
The following figure shows a front view of the vehicle.
|
Unit: mm (in) : vehicle front |
Rear view
The following figure shows a rear view of the vehicle.
|
Unit: mm (in) : vehicle front |
MEASUREMENT POINTS (FRAME)
| : vehicle front |
Unit: mm (in)
| Points | Coordinates | Remarks | Points | Coordinates | Remarks | ||||
|---|---|---|---|---|---|---|---|---|---|
| X | Y | Z | X | Y | Z | ||||
|
±436.0 (±17.166) |
-563.2 (-22.172) |
219.4 (8.637) |
Hole φ16 (0.63) | |
450.0 (17.717) |
3721.5 (146.515) |
352.8 (13.890) |
Hole φ28 (1.10) |
|
±603.5 (±23.760) |
-555.0 (-21.850) |
356.8 (14.047) |
Hole φ32 (1.26) | |
-373.0 (-14.685) |
3721.5 (146.515) |
348.3 (13.713) |
Hole 34×28 (1.34×1.10) |
|
±466.3 (±18.359) |
-282.7 (-11.129) |
204.3 (8.041) |
Hole φ12 (0.47) | |
±645.0 (±25.394) |
3980.0 (156.693) |
406.0 (15.984) |
Hole φ65 (2.56) |
|
±673.0 (±26.496) |
612.7 (24.122) |
224.8 (8.850) |
Hole φ71 (2.80) |  |
±556.2 (±21.898) |
4064.9 (160.033) |
246.7 (9.713) |
Hole φ17 (0.67) |
|
±469.0 (±18.465) |
721.0 (28.386) |
56.1 (2.209) |
Hole 39×24 (1.54×0.94) |   |
±428.6 (±16.874) |
-728.4 (-28.677) |
348.7 (13.728) |
Hole φ15 (0.59) |
|
±381.4 (±15.017) |
908.2 (35.756) |
47.8 (1.883) |
Hole φ10 (0.39) |  |
428.6 (16.874) |
-728.4 (-28.677) |
242.9 (9.562) |
Hole 19×15 (0.75×0.59) |
|
±636.2 (±25.047) |
1723.4 (67.851) |
58.4 (2.299) |
Hole φ8 (0.31) |  |
-428.6 (-16.874) |
-728.4 (-28.677) |
242.9 (9.562) |
Hole 19×15 (0.75×0.59) |
|
±615.3 (±24.224) |
2339.2 (92.092) |
40.5 (1.594) |
Hole φ8 (0.31) |   |
±498.7 (±19.633) |
5.6 (0.221) |
593.9 (23.382) |
Hole φ78 (3.07) |
|
±678.0 (±26.693) |
2440.0 (96.063) |
301.6 (11.874) |
Hole φ32 (1.26) |   |
±596.8 (±23.495) |
2871.6 (113.056) |
445.6 (17.544) |
Hole φ66 (2.60) |
|
±285.0 (±11.220) |
2852.6 (112.307) |
180.0 (7.087) |
Hole φ16 (0.63) |   |
±550.9 (±21.689) |
4110.0 (161.811) |
331.7 (13.059) |
Hole φ15 (0.59) |
|
±555.7 (±21.878) |
3234.5 (127.342) |
286.3 (11.271) |
Hole φ55 (2.17) |   |
±550.9 (±21.689) |
4110.0 (161.811) |
276.7 (10.894) |
Hole φ15 (0.59) |
Passenger Compartment
WARNING:
-
Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.
MEASUREMENT (EXTERIOR)
Dimensions marked with ″″ indicate symmetrically identical dimensions on both the right and left hand of the vehicle.
| Unit: mm (in) |
Unit: mm (in)
| Point | Dimension | Memo | Point | Dimension | Memo | Point | Dimension | Memo |
|---|---|---|---|---|---|---|---|---|
| – |
1591 (62.64) | – |
1892 (74.49) |
– |
849 (33.43) | |||
| – |
1785 (70.28) |
– |
1647 (64.84) | – |
909 (35.79) | |||
| – |
1788 (70.39) |
– |
2019 (79.49) |
– |
1066 (41.97) |
|||
| – |
1889 (74.37) |
– |
1766 (69.53) |
– |
839 (33.03) |
|||
| – |
1647 (64.84) | – |
1485 (58.46) | – |
623 (24.53) |
|||
| – |
1891 (74.45) |
– |
1829 (72.01) |
– |
1225 (48.23) |
|||
| – |
1636 (64.41) | – |
1639 (64.53) | – |
1027 (40.43) |
|||
| – |
2092 (82.36) |
– |
1642 (64.65) | – |
644 (25.35) |
|||
| – |
1848 (72.76) |
– |
1115 (43.90) | – |
1800 (70.87) | |||
| – |
1527 (60.12) | – |
1160 (45.67) | –  |
1139 (44.84) |
|||
| – |
1813 (71.38) |
– |
1053 (41.46) | –  |
1197 (47.13) |
|||
| – |
1667 (65.63) | – |
1102 (43.39) | – |
1851 (72.87) | |||
| – |
1646 (64.80) | – |
954 (37.56) | – |
1216 (47.87) |
|||
| – |
1527 (60.12) | – |
1008 (39.68) | – |
1159 (45.63) |
|||
| – |
1806 (71.10) |
– |
1245 (49.02) | –  |
1794 (70.63) | |||
| – |
1727 (67.99) |
– |
1284 (50.55) | –  |
1823 (71.77) | |||
| – |
1902 (74.88) |
– |
1050 (41.34) | — | — | |||
| – |
1672 (65.83) | – |
1100 (43.31) | — | — |
MEASUREMENT POINTS (EXTERIOR)
| : vehicle front |
Unit: mm (in)
| Point | Material | Point | Material |
|---|---|---|---|
|
Cowl top flange end | |
Center pillar indent |
|
Roof flange end of center positioning mark | |
Rear fender indent |
|
Outer side body joggle | |
Front floor reinforcement hole center φ7 (0.28) |
|
Outer side body indent | |
Rear floor front extension hole center
: 17×15 (0.67×0.59) |
|
Front pillar indent | |
Door hinge installing hole center φ12 (0.47) |
MEASUREMENT (INTERIOR)
Dimensions marked with ″″ indicate symmetrically identical dimensions on both the right and left hand of the vehicle.
| Unit: mm (in) |
Unit: mm (in)
| Point | Dimension | Memo | Point | Dimension | Memo | Point | Dimension | Memo |
|---|---|---|---|---|---|---|---|---|
| – |
1488 (58.58) | – |
1453 (57.20) | – |
1469 (57.83) | |||
| – |
1155 (45.47) | – |
1284 (50.55) | – |
1924 (75.75) | |||
| – |
1751 (68.94) |
– |
1422 (55.98) |
– |
1553 (61.14) |
MEASUREMENT POINTS (INTERIOR)
| : vehicle front |
Unit: mm (in)
| Point | Material | Point | Material |
|---|---|---|---|
|
Upper inner front pillar hole center φ7 (0.28) | |
Front floor reinforcement hole center φ7 (0.28) |
|
Inner center pillar hole center φ15 (0.59) | |
Rear floor front extension hole center
: 17×15 (0.67×0.59) |
|
Inner rear pillar hole center φ15 (0.59) | — | — |
Rear Body
WARNING:
-
Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.
MEASUREMENT
Dimensions marked with ″″ indicate symmetrically identical dimensions on both the right and left hand of the vehicle.
| Unit: mm (in) |
Unit: mm (in)
| Point | Dimension | Memo | Point | Dimension | Memo | Point | Dimension | Memo |
|---|---|---|---|---|---|---|---|---|
| – |
703 (27.68) |
– |
2653 (104.45) |
– |
1473 (57.99) | |||
| – |
787 (30.98) |
– |
1356 (53.39) | – |
530 (20.87) |
|||
| – |
1123 (44.21) |
– |
1397 (55.00) | – |
1123 (44.21) |
|||
| – |
1360 (53.54) |
– |
563 (22.17) |
– |
1353 (53.27) |
|||
| – |
2423 (95.39) |
– |
1217 (47.91) |
– |
2310 (90.94) |
|||
| – |
1339 (52.72) |
– |
1481 (58.31) |
– |
2660 (104.72) |
|||
| – |
1544 (60.79) |
– |
2261 (89.02) |
– |
1176 (46.30) |
|||
| – |
2289 (90.12) |
– |
2699 (106.26) |
– |
2484 (97.80) |
MEASUREMENT POINTS
| : vehicle front |
Unit: mm (in)
| Point | Material | Point | Material |
|---|---|---|---|
|
Roof indent of center positioning mark | |
Center rear crossmember joggle |
|
Back pillar main joggle | |
Rear crossmember flange end |
|
Back pillar main hole center
: φ7 (0.28) |
|
3rd seat front mounting bracket
: φ12 (0.47) |
|
Rear combination lamp base joggle | |
Center pillar indent |
|
Rear combination lamp base hole center □9 (0.35) | — | — |
Other materials
Second Seat Belt
Exploded View
CAPTAIN SEAT
Seat belt hook RH
Anchor bolt
Seat belt pre-tensioner retractor RH
Seat belt pre-tensioner retractor LH
Seat belt hook LH
Retaining washer
Spacer
Bush
Shoulder anchor LH
Shoulder anchor RH
Seat belt finisher LH
Seat belt finisher RH
...
Additional Service When Replacing Ecm
Description
Performing the following procedure can automatically activate recommunication of ECM and Intelligent Key unit, but only when the ECM is replaced with a new one*. For details, refer to Work Procedure.*: New one means a virgin ECM that has never been energized on-board.(In this step, initi ...
Additional Service When Replacing Audio Amp.
Work Procedure
CAUTION:
When after replacing audio amp, Configuration must be performed. Or not doing so, audio amp. control function does not operate normally.REPLACE AUDIO AMP.
Replace audio amp. Refer to Removal & Installation.
>>
GO TO 2.
PERFORM AUDIO amp. CONFIGURATION
Perform aud ...