Work Flow
DETAILED FLOW
INTERVIEW FROM THE CUSTOMER
CAUTION:
Customers are not professional. Never guess easily like “maybe the customer means that...,” or “ maybe the customer mentions this symptom”.
>>
GO TO 2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-safe.
CAUTION:
When the symptom is caused by normal operation, fully inspect each portion and obtain the understanding of customer that the symptom is not caused by a malfunction.
>>
GO TO 3.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for "Driving Video Recorder".
Is DTC detected?
YES>>Record or print self-diagnosis results and freeze frame data (FFD). GO TO 4.
NO>>INSPECTION END
PERFORM DTC DIAGNOSIS PROCEDURE
With CONSULT
Perform DTC confirmation procedures for the error-detected system.
NOTE:
If some DTCs are detected at the same time, determine the order for performing the diagnosis. Refer to DTC Inspection Priority Chart.
Is DTC detected?
YES>>GO TO 5.
NO>>Check harness and connectors based on the information obtained by interview.
REPAIR OR REPLACE ERROR-DETECTED PARTS
With CONSULT
-
Repair or replace error-detected parts.
-
Reconnect part or connector after repairing or replacing.
-
When DTC is detected, erase self-diagnostic result for “Driving Video Recorder”.
>>
GO TO 6.
FINAL CHECK
With CONSULT
-
Check the "Values On The Diagnosis Tool" for "Driving Video Recorder".
-
Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES>>GO TO 3.
NO>>INSPECTION END
Diagnostic Work Sheet
DESCRIPTION
-
In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
INTERVIEW SHEET SAMPLE
| Interview sheet | |||||
|---|---|---|---|---|---|
| Customer name | MR/MS | Registration number | Initial year registration | ||
| vehicle type | VIN | ||||
| Storage date | Engine / Traction motor | Mileage | km (Mile) | ||
| Symptom | □ Does not operate ( | ) function | |||
| □ Warning lamp for ( | ) turns ON. | ||||
| □ Noise □ Vibration | |||||
| □ Other ( | ) | ||||
| First occurrence | □ Recently □ Other ( | ) | |||
| Frequency of occurrence | □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day) | ||||
| Climate conditions | □ Irrelevant | ||||
| Weather | □ Fine □ Cloud □ Rain □Snow □ Others ( | ) | |||
| Temperature | □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. | °C (°F)] | |||
| Relative humidity | □ High □ Moderate □ Low | ||||
| Road conditions | □ Urban area □ Suburb area □ Highway □ Mountainous road (uphill or downhill) □ Rough road | ||||
| Operating condition, etc. |
□ Irrelevant □ When engine/traction motor starts □ During idling □ During driving □ During acceleration □ At constant speed driving □ During deceleration □ During cornering (right curve or left curve) □ When steering wheel is steered (to right or to left) |
||||
| Other conditions | |||||
| vehicle equipment | |||||
| Memo | |||||
Other materials
Changing wheels and tires
Tire rotation
To maintain optimal performance and extend tire life on your Nissan Armada, it
is strongly recommended to rotate the tires at regular intervals of approximately
10,000 miles (16,000 km).
Consistent tire rotation helps ensure even tread wear, improves ride comfort,
and contr ...
Brake System Service Data and Specifications
General Specifications
BRAKE SYSTEMUnit: mm (in) Front brake
Cylinder bore diameter
50.8 × 2 (2.000 × 2)
Pad length × width × thickness
151.6 × 53.2 × 12.0 (5.97 × 2.094 × 0.47)
Rotor outer diameter × thickness
350.0 × 30.0 (13.78 × 1.18)
Rear brake
Cylinder bore diamet ...
Glass & Window System Tools and Preparation
Special Service Tools
The actual shapes of TechMate tools may differ from those of special service tools illustrated here.
Tool number
(TechMate No.)
Tool name Description
(NI-39570)
Chassis ear
Locates the noise
(NI-50397)
NISSAN Squeak and Rattle Kit
Repairs the cause of noise
C ...