Nissan Armada 2025-2026 Service and Repair Manual: Power Outlet. Power Socket

Precautions

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.

Precautions for Removing Battery Terminal

• When disconnecting the 12V battery terminal, turn off the ACC power before disconnecting the 12V battery terminal, observing “How to disconnect 12V battery terminal” described below.

  

  NOTE:

  Some ECUs operate for a certain fixed time even after ignition switch is turned OFF and ignition power supply is stopped. If the battery terminal is disconnected before ECU stops, accidental DTC detection or ECU data damage may occur.

• For Nissan Armada vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON the ignition switch.

  NOTE:

  If the ignition switch is turned ON with any one of the terminals of main battery and sub battery disconnected, then DTC may be detected.

• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

  NOTE:

  The removal of 12V battery may cause a DTC detection error.

HOW TO DISCONNECT 12V BATTERY TERMINAL

Disconnect 12V battery terminal according to instruction described below.

1. Open the hood.

2. Turn ignition switch to the ON position.

3. Turn ignition switch to the OFF position with the driver side door opened.

4. Get out of the vehicle and close the driver side door.

5. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse of the specified time.

   BR08DE	: 4 minutes	R9N engine	: 12 minutes
   BR10DE	: 12 minutes	V9X engine	: 4 minutes
   D4D engine	: 20 minutes	YD25DDTi	: 2 minutes
   HR09DET	: 12 minutes	YS23DDT	: 4 minutes
   HR10DDT	: 12 minutes	YS23DDTT	: 4 minutes
   HR10DET	: 12 minutes	ZD30DDTi	: 60 seconds
   HR13DDT	: 12 minutes	ZD30DDTT	: 60 seconds
   HRA2DDT	: 12 minutes	K9K engine	: 4 minutes
   M9R engine	: 4 minutes	R9M engine	: 4 minutes

   CAUTION:

   While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of this caution results in the activation of ACC power supply according to the Auto ACC function.

6. Remove 12V battery terminal.

   CAUTION:

   After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.

Power Socket

Power Socket (front)

Removal and Installation

REMOVAL

Remove front center console body assembly. Refer to Removal and Installation.

Press the power socket fixing pawls from the back of the front center console body assembly to remove the power socket.

: Pawl

INSTALLATION

Note the following, and then install in the reverse order of removal.

CAUTION:

Align the cut out of power socket and front center console body assembly.

: Cut out

Power Socket (second)

Removal and Installation

REMOVAL

Make a clearance by remove rear end portion of front center console rear finisher assembly. Refer to Exploded View.

Press the power socket fixing pawls from the back of the front center console rear finisher assembly to extrude the power socket.

: Pawl

Disconnect harness connector, and then remove the power socket.

INSTALLATION

Note the following, and then install in the reverse order of removal.

CAUTION:

Align the cut out of power socket and front center console rear finisher assembly.

: Cut out