NIARMADA Nissan Armada manuals & owner information
Nissan Armada owner resource

Manuals, service information and practical owner guidance.

Fast access to Nissan Armada manuals, operating instructions, maintenance references and technical information.

Browse manuals →
Nissan Armada manual library

Nissan Armada 2025-2026 Service and Repair Manual: Precautions

Nissan Armada 2025-2026 Service and Repair Manual / Driver Information & Multimedia / Audio, Visual & Navigation System. Around View Monitor / Precautions

PRECAUTIONS FOR SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG AND SEAT BELT PRE-TENSIONER : Precautions

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.

  • Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”.

  • Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.

  • When using air or electric power tools or hammers, always switch the ignition/power switch OFF, disconnect the 12V battery or batteries, and wait at least 3 minutes before performing any service.

PRECAUTIONS FOR REMOVING BATTERY TERMINAL : Precautions

  • When disconnecting the 12V battery terminal, turn off the ACC power before disconnecting the 12V battery terminal, observing “How to disconnect 12V battery terminal” described below.

    NOTE:

    Some ECUs operate for a certain fixed time even after ignition switch is turned OFF and ignition power supply is stopped. If the battery terminal is disconnected before ECU stops, accidental DTC detection or ECU data damage may occur.

  • For Nissan Armada vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON the ignition switch.

    NOTE:

    If the ignition switch is turned ON with any one of the terminals of main battery and sub battery disconnected, then DTC may be detected.

  • After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

    NOTE:

    The removal of 12V battery may cause a DTC detection error.

HOW TO DISCONNECT 12V BATTERY TERMINAL

Disconnect 12V battery terminal according to instruction described below.

  1. Open the hood.

  2. Turn ignition switch to the ON position.

  3. Turn ignition switch to the OFF position with the driver side door opened.

  4. Get out of the vehicle and close the driver side door.

  5. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse of the specified time.

    BR08DE : 4 minutes R9N engine : 12 minutes
    BR10DE : 12 minutes V9X engine : 4 minutes
    D4D engine : 20 minutes YD25DDTi : 2 minutes
    HR09DET : 12 minutes YS23DDT : 4 minutes
    HR10DDT : 12 minutes YS23DDTT : 4 minutes
    HR10DET : 12 minutes ZD30DDTi : 60 seconds
    HR13DDT : 12 minutes ZD30DDTT : 60 seconds
    HRA2DDT : 12 minutes K9K engine : 4 minutes
    M9R engine : 4 minutes R9M engine : 4 minutes

    CAUTION:

    While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of this caution results in the activation of ACC power supply according to the Auto ACC function.

  6. Remove 12V battery terminal.

    CAUTION:

    After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.

PRECAUTIONS FOR TROUBLE DIAGNOSIS : Precautions

AV COMMUNICATION SYSTEM

  • Do not apply voltage of 7.0 V or higher to the measurement terminals.

  • Use the tester with its open terminal voltage being 7.0 V or less.

  • Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before checking the circuit.

PRECAUTIONS FOR HARNESS REPAIR : Precautions

AV COMMUNICATION SYSTEM

  • Solder the repaired parts, and wrap with tape. [Frays of twisted line must be within 110 mm (4.33 in).]

  • Do not perform bypass wire connections for the repair parts. (The spliced wire will become separated and the characteristics of twisted line will be lost.)

    Other materials

    Brake Pedal Vibration or Operation Sound Occurs
    Description Brake pedal vibrates and motor sound from ABS actuator and electric unit (control unit) occurs, when the engine starts. Brake pedal vibrates during braking. CAUTION: Vibration may be felt during brake pedal is lightly depressed (just placing a foot on it) in the following conditions ...

    Normal Operating Condition
    Description LED HEADLAMP LED brightness and color may slightly change until the temperature becomes stable. This is not malfunction. Illumination time lag may occur between right and left. This is not malfunction. Brightness may be reduced due to aged deterioration of LED. INTELLIGENT AUTO LIG ...

    Precautions
    Precautions for Trouble Diagnosis CAUTION: Follow the instructions listed below. Failure to do this may cause damage to parts: Never apply 7.0 V or more to the measurement terminal. Use a tester with open terminal voltage of 7.0 V or less. Turn the ignition switch OFF and disconnect the batter ...