Nissan Armada 2025-2026 Service and Repair Manual: Safety Section
The occupational safety regulations include provisions on preventative measures for avoiding damage and accidents. As the occupational safety regulations are country- specific, this document only lists general information on occupational health and safe- ty for working with steel. The general, non-material-specific protection and hygiene measures in the workshop must always be observed.
Protective equipment
The following table provides an overview of the general personal protective equipment for material processing:
| Protective equipment | MAG welding | Spot welding | Sanding / Grinding & Cutting |
| Protective shoes | X | X | X |
| Work clothing | X | X | X |
| Safety goggles | X | X | |
| Welding gloves | X | ||
| General protection gloves | X | X | |
| General apron | |||
| Latex gloves | |||
| Fine dust mask | X | ||
| Breathing protection with filter* | |||
| Ear defenders | X | ||
| Welding apron, clothing suitable for welding | X | X | |
| Welding shield, welding mask | X |
*only if there is insufficient ventilation
The up-to-date guidelines and notes in the workshop information system ISTA must always be observed. In addition to the general protective equipment, country-specific provisions must also be complied with where applicable.
Working area
A safe and high-quality working environment requires cleanliness and order. When processing steel components, workers must always not only ensure that they themselves are safe, but also that other work bays and employees are not put at risk.
| Protective equipment | MAG welding | Spot Welding | Sanding / Grinding & Cutting | Bonding |
| Partition walls, protective curtains | X | X | X | |
| Welding emission extraction | X |
A fire extinguisher must always be close to hand during work with a raised level of fire risk for example MAG welding.
The up-to-date guidelines and notes in the workshop information system ISTA must always be observed. In addition to the general protective measures for the working area, country- specific provisions must also be complied with where applicable.
Tools
The general and country-specific safety regulations for work with tools for processing metal must be complied with.
The general safety regulations are:
Do not clean tools with compressed air.
Do not use abrasives that have already been used for processing aluminum.
Always separate tools for steel processing and aluminum processing.
Environment
The proper disposal and recycling of materials are described in the environmental protection law. The laws serve to protect natural resources and preserve the environment. Environmental protection laws are regulated on a market-specific basis.
Recycling
Scrap metals from vehicles are largely recyclable. The steel is added to the steel production process.
To separate the various materials in the body shell, the body shell is compressed into a bundle and shredded. The shredded material is separated into ferrous metals, non- ferrous metals and other materials. This is done with the sink-float method using their different weights.
Protectors
While working, suitable work clothes, a work cap and safety shoes must be worn. To prevent burns, a long sleeve shirt and trousers must also be worn and must not be taken off under any circumstances.
...
Safety Stand
After jacking up a vehicle body, be sure to support it with the safety stand. For the supporting positions, refer to “Lifting Points” in the Service Manual for each model. ...
Other materials:
Symptom Table
Symptom Possible cause Inspection item/Work item ””is displayed Front camera (driving video recorder) abnormality
Rear camera (driving video recorder) abnormality
Inside camera (driving video recorder) abnormality
Perform diagnosis procedure ”” is displayed Wi-Fi abnormality Perfor ...
Precautions for High Strength Steel (HSS) and Ultra High Strength Steel (UHSS)
High strength steel (HSS) means the steel from 440 MPa - 979 MPa.
Ultra high strength steel (UHSS) means the steel above 980 MPa.
(a) The repair of reinforcements (such as side members) by heating is not recommended since it may weaken the component. When heating is unavoidable, do not heat HSS part ...
Work Procedure
Memory Storage Procedure
Two positions for the seat, steering column, and door mirror can be stored for memory operation by following procedure.
NOTE:
Memory registration can be performed with no restrictions of the shift position, vehicle speed, and ignition switch position.
REGISTRATION METHOD
Adj ...
0.0077