NIARMADA Nissan Armada manuals & owner information
Nissan Armada owner resource

Manuals, service information and practical owner guidance.

Fast access to Nissan Armada owner manuals, service procedures, maintenance references, technical information and practical guides for different Armada generations.

Browse manuals →
Nissan Armada manual library

Nissan Armada 2025-2026 Service and Repair Manual: Shift Position

Nissan Armada 2025-2026 Service and Repair Manual / Transmission & Driveline / Transaxle & Transmission. 9at: Ge9r01a / Shift Position

Inspection

CHECK SHIFT BUTTON OPERATION

  1. When pressing each shift button of electric shift selector, check that each button is not twisted, stuck, or does not make noise and can be operated smoothly.

  2. After pressing each shift button, check that all buttons return to original positions without sticking.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the electric shift selector. Refer to Removal and Installation.

CHECK SHIFT POSITION

Check the following during engine running.

  1. When pressing each shift button while depressing brake pedal, check shift position is changed according to the shift button.

  2. When pressing each shift button without depressing brake pedal during P position, check that shift position is not changed from P position.

  3. When pressing R button while depressing brake pedal, check that the reverse lamp turns on and the single tone sounds to notify the driver.

  4. When pressing D/M button during D position, check that the mode is switched to manual mode (shift position is displayed numerically).

  5. When pressing D/M button during manual mode, check that shift position is changed to D position.

  6. When the ignition switch turns off, the shift position automatically changes into the P position. (The indicator lamp of the P button turns ON.)

Is the inspection result normal?

YES>>

END

NO>>

Check the electric shift system.

How to Erase Pearmanent Dtc

Description

WHEN A DTC IS STORED IN TCM

When a DTC is stored in TCM and MIL is ON, a permanent DTC is erased with MIL shutoff if the same malfunction is not detected after performing the driving pattern for MIL shutoff three times in a raw.

NOTE:

The following timing chart is for DTC of two trip detection diagnosis.

In case of DTC of one trip detection diagnosis, when NG is detected at one trip, MIL turns ON and permanent DTC is displayed.

*1: When the same malfunction is detected in two consecutive trips, MIL will illuminate. *2: MIL will turn off after vehicle is driven 3 times (driving pattern B) without any malfunctions. *3:

Diagnosis condition *A and diagnosis delay time *A for each DTC are satisfied.

(*A: For details of these, refer to DTC/CIRCUIT DIAGNOSIS >> DTC (Pxxxx or Uxxx) >> DTC Description >> DTC DETECTION LOGIC.)

WHEN A DTC IS NOT STORED IN TCM

The erasing method depends on a permanent DTC stored in TCM.

For erase procedure of permanent DTC, refer to Work Procedure.

PERMANENT DTC ITEM

For permanent DTC items, MIL turns ON. Refer to DTC Index.

Work Procedure

CHECK DTC

Check DTC.

Is any DTC detected?

YES>>

Repair malfunction(s) and erase DTC.

NO>>

GO TO 2.

CHECK PERMANENT DTC

With CONSULT

  1. Ignition switch OFF and wait at least 60 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 60 seconds.

  4. Ignition switch ON.

  5. Select “PERMANENT DTC STATUS” mode with CONSULT.

With GST

  1. Ignition switch OFF and wait at least 60 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 60 seconds.

  4. Ignition switch ON.

  5. Select Service $0A with GST.

Is any permanent DTC detected?

YES>>

GO TO 3.

NO>>

END

HOW TO ERASE PERMANENT DTC

CAUTION:

Always drive at a safe speed.

  1. Perform "DTC CONFIRMATION PROCEDURE "of detected permanent DTC.

  2. Drive the vehicle following to driving pattern.

    • The state of driving at 40 km/h (25 MPH) reaches 300 seconds or more in total.

    • Idle speed lasts 30 seconds or more.

    • A lapse of 600 seconds or more after engine start.

>>

GO TO 4.

CHECK PERMANENT DTC

With CONSULT

  1. Ignition switch OFF and wait at least 60 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 60 seconds.

  4. Ignition switch ON.

  5. Select “PERMANENT DTC STATUS” mode with CONSULT.

With GST

  1. Ignition switch OFF and wait at least 60 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 60 seconds.

  4. Ignition switch ON.

  5. Select Service $0A with GST.

Is any permanent DTC detected?

YES>>

GO TO 1.

NO>>

END

    Other materials

    About microSD card
    WARNING Never allow children to handle or play with the microSD card used in your Nissan Armada. Due to its small size, accidental swallowing may occur, which can lead to choking, serious injury, or even life-threatening situations. NOTE: If the microSD card is removed from the Nissan Armada ...

    Break-in schedule
    CAUTION During the initial 1,200 miles (2,000 km), it is essential to follow these guidelines carefully to ensure optimal engine performance, long-term durability, and maximum efficiency of your Nissan Armada. Ignoring these break-in recommendations for your Nissan Armada may lead to prematu ...

    Towing safety
    Trailer hitch Your Nissan Armada is equipped with a factory-installed trailer towing package designed to support reliable and safe towing operations. This package includes a robust, frame-mounted receiver-type hitch that is engineered to handle the maximum towing capacity of the Nissan Armada ...