Exploded View
 |
Drive pinion lock nut |  |
Companion flange |  |
Front oil seal |
 |
Pinion front bearing |  |
Collapsible spacer |  |
Gasket |
 |
Filler plug |  |
Drain plug |  |
Mounting insulator |
 |
Gear carrier |  |
Mounting insulator |  |
Breather connector |
 |
Side shaft bearing |  |
Snap ring |  |
Snap ring |
 |
Side oil seal |  |
Side shaft |  |
Pinion rear bearing |
 |
Pinion height adjusting washer |  |
Drive pinion |  |
Drive gear |
 |
Differential assembly |  |
Carrier cover |  |
Bearing cap |
 |
Side bearing |  |
Side bearing adjusting washer |  |
Spacer |
 |
Side oil seal | ||||
 |
Screw hole |  |
Comply with the assembly procedure when tightening. Refer to Disassembly and Assembly. | ||
 : N·m (kg-m, ft-lb) |
|||||
 : Always replace after every disassembly. |
|||||
 : Select with proper thickness. |
|||||
 : Apply Genuine Liquid Gasket, Three Bond 1217 or equivalent. Refer to Recommended Chemical Products and Sealants. |
|||||
 : Apply Genuine High Strength Thread Locking Sealant, Loctite 270 or equivalent. Refer to Recommended Chemical Products and Sealants. |
|||||
Disassembly and Assembly
DISASSEMBLY
Remove the carrier cover bolts.
Remove carrier cover to insert the seal cutter (A) [SST: KV10111100 (NI-37228)] between gear carrier and carrier cover.
CAUTION:
-
Never damage the mating surface.
-
Never insert flat-bladed screwdriver, this will damage the mating surface.
Remove side oil seal with oil seal remover (A) (commercial service tool).
CAUTION:
Never damage gear carrier.
Remove snap ring (hole side) with a snap ring pliers (A).
Remove differential side shaft assembly out of gear carrier with a suitable tool.
NOTE:
Tap on side shaft assembly from side gear side.
Remove snap ring (side shaft side).
Press side shaft out of side shaft bearing .
CAUTION:
Never drop side shaft.
Perform inspection after disassembly. Refer to Inspection.
ASSEMBLY
Press side shaft bearing to side shaft .
CAUTION:
Never reuse side shaft bearing.
Install snap ring (side shaft side).
Install side shaft assembly into gear carrier.
Install snap ring (hole side).
Install side oil seal until it becomes flush with the gear carrier, with the drifts (A and B).
| A | : Drift [SST: ST30720000 (NI-25405)] |
| B | : Drift [SST: ST27863000 ( — )] |
NOTE:
For left side, use drift [SST: ST30720000 (NI-25405)] only.
CAUTION:
-
Never reuse oil seal.
-
When installing, never incline oil seal.
-
Check that the oil seal lip is filled up with grease.
Inspection
INSPECTION AFTER DISASSEMBLY
Side Shaft
-
If it is chipped (by friction), cracked, damaged, or unusually worn, replace.
Oil Seal
-
Whenever disassembled, replace.
-
If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace.
Other materials
Roof rack
Example
Basic information
WARNING
In the Nissan Armada, always install the crossbars onto the roof side
rails before placing any cargo. Loading items directly onto the roof rails or
roof surface may result in vehicle damage.
Ensure that Nissan Armada roof rack crossbars are mounted ...
Additional Service When Replacing Ecm
Description
When replacing ECM, the following procedure must be performed. (For details, refer to Work Procedure.)CAUTION:
When replacing the ECM, always replace it with a new one. The functions controlled by the ECM does not operate properly in case of reuse of the ECM from another vehicle.PROGRAMM ...
Precautions
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger fo ...