NIARMADA Nissan Armada manuals & owner information
Nissan Armada owner resource

Manuals, service information and practical owner guidance.

Fast access to Nissan Armada owner manuals, service procedures, maintenance references, technical information and practical guides for different Armada generations.

Browse manuals →
Nissan Armada manual library

Nissan Armada 2025-2026 Service and Repair Manual: A/t Fluid Cooler

Nissan Armada 2025-2026 Service and Repair Manual / Transmission & Driveline / Transaxle & Transmission. 9at: Ge9r01a / A/t Fluid Cooler

Exploded View

Bracket A/T fluid cooler air guide RR A/T fluid cooler
A/T fluid cooler air guide FR Bracket    
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)

Removal and Installation

WARNING:

  • Jacking up or lift up the vehicle may the vehicle height to go down which cause a personal injury and/or damage to the air suspension component parts. Refer to Precaution for when Jacking and Lifting Up the vehicle with Electronic Air Suspension System.

REMOVAL

NOTE:

When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spilling.

CAUTION:

Perform this step when the engine is cold.

Remove Front bumper. Refer to Exploded View.

Remove clip () and remove A/T fluid cooler air guide FR from A/T fluid cooler.

Remove A/T fluid cooler hose A from the A/T fluid cooler using the following procedure:

  1. Remove A/T fluid cooler hose cap from A/T fluid cooler hose A .

  2. Install suitable disconnect tool (A) (commercial service tool) on to the A/T fluid cooler hose A at the A/T fluid cooler side.

  3. Rotate suitable disconnect tool (A) (commercial service tool) counter clockwise 60 degrees to release snap ring.

  4. Remove A/T fluid cooler hose A from the A/T fluid cooler.

Remove A/T fluid cooler hose B from A/T fluid cooler using the following procedure:

  1. Remove A/T fluid cooler hose cap from A/T fluid cooler hose B .

  2. Install suitable disconnect tool (A) (commercial service tool) on to the A/T fluid cooler hose B at the A/T fluid cooler side.

  3. Rotate suitable disconnect tool (A) (commercial service tool) counter clockwise 60 degrees to release snap ring.

  4. Remove A/T fluid cooler hose B from the A/T fluid cooler.

  5. Remove clip () from A/T fluid cooler.

  6. Remove A/T fluid cooler mount bolt () and remove A/T fluid cooler .

  7. Remove clip () and remove A/T fluid cooler air guide RR from A/T fluid cooler.

  8. Remove bracket mounting bolt () and remove bracket .

INSTALLATION

Installation is in the reverse order of removal.

Inspection and Adjustment

INSPECTION AFTER INSTALLATION

Check for A/T fluid leakage. Refer to Inspecton.

ADJUSTMENT AFTER INSTALLATION

Adjust A/T fluid level. Refer to Adjustment.

    Other materials

    Front Shock Absorber
    Exploded View WITHOUT DYNAMIC DIGITAL SUSPENSION AND ELECTRONIC AIR SUSPENSION Piston rod lock nut Mounting insulator Rubber seat Coil spring Dust cover Bound bumper Shock absorber Lower link     : Always replace after every disassembly. : N·m (kg-m, ft-l ...

    Rear Cooler Pipe Assembly
    Removal and Installation REMOVALCAUTION: Perform lubricant return operation before each refrigeration system disassembly. However, if a large amount of refrigerant or lubricant leak is detected, never perform lubricant return operation. Refer to Perform Lubricant Return Operation. When disconnec ...

    Front Door Glass Run
    Removal and Installation REMOVALCAUTION: Never excessively pull front door glass run.Fully open front door glass. Remove front door sash cover. Refer to Removal and Installation. Remove front door sash inner cover. Refer to Removal and Installation. Remove front door glass run according to numerical ...