NIARMADA Nissan Armada manuals & owner information
Nissan Armada owner resource

Manuals, service information and practical owner guidance.

Fast access to Nissan Armada owner manuals, service procedures, maintenance references, technical information and practical guides for different Armada generations.

Browse manuals →
Nissan Armada manual library

Nissan Armada 2025-2026 Service and Repair Manual: Fillet Molding

Nissan Armada 2025-2026 Service and Repair Manual / Body Exterior, Doors, Roof & Vehicle Security / Exterior / Fillet Molding

Exploded View

Front fillet molding Rear fillet molding front Rear fillet molding rear
Grommet

Double-sided tape

[t: 1.2 mm (0.047 in)] 		   
: Clip
: Pawl
: vehicle front
: Always replace after every disassembly.

Front Fillet Molding

Removal and Installation

REMOVAL

Remove front fillet molding fixing screws .

Apply protective tape (A) on the part to protect it from damage.

Disengage front fillet molding fixing pawl indicated by arrows as shown in the figure.

: Pawl

Disengage fixing clips, and then remove front fillet molding indicated by arrows as shown in the figure.

: Clip

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

  • Always replace double-sided tape with a new one, if front fillet molding is reused.

  • Remove double-sided tape remaining on front fender panel and back of front fillet molding with a double-sided tape remover, after removing front fillet molding.

  • Degrease front fillet molding mounting surface of front fender panel.

  • Paint grain or dust on mounting surface of front fillet molding may spoil exterior appearance if it remains. Clean the mounting surface and check that no paint grain or dust remains, before starting the operation.

  • When installing front fillet molding, visually check the clips, then replace it with new parts if they are damaged.

  • When installing front fillet molding, check that clips are securely fitted in fender panel holes, and then press it in.

  • Never wash the vehicle within 24 hours after installing so as to keep adhesive.

Rear Fillet Molding Front

Removal and Installation

REMOVAL

Apply protective tape (A) on the part to protect it from damage.

Insert a remover tool (A) between rear fillet molding front and rear door panel, cut double-sided tape using a cutter (B) while lifting rear fillet molding front.

Disengage fixing clips, and then remove rear fillet molding front indicated by arrows as shown in the figure.

: Clip

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

  • Always replace double-sided tape with a new one, if rear fillet molding front is reused.

  • Remove double-sided tape remaining on rear door panel and back of rear fillet molding front with a double-sided tape remover, after removing rear fillet molding front.

  • Degrease rear fillet molding front door panel mounting surface of rear door panel.

  • Paint grain or dust on mounting surface of rear fillet molding front may spoil exterior appearance if it remains. Clean the mounting surface and check that no paint grain or dust remains, before starting the operation.

  • When installing rear fillet molding front, visually check the clips, then replace it with new parts if they are damaged.

  • When installing rear fillet molding front, check that clips are securely fitted in rear door panel holes, and then press it in.

  • Never wash the vehicle within 24 hours after installing so as to keep adhesive.

Rear Fillet Molding Rear

Removal and Installation

REMOVAL

Remove rear fillet molding rear fixing clips and screws .

Apply protective tape (A) on the part to protect it from damage.

Insert a remover tool (A) between rear fillet molding rear and rear fender panel, and then cut double-sided tape using a cutter (B) while lifting rear fillet molding rear.

Disengage fixing clips, and then remove rear fillet molding rear indicated by arrows as shown in the figure.

: Clip

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

  • Always replace double-sided tape with a new one, if rear fillet molding rear is reused.

  • Remove double-sided tape remaining on rear fender panel and back of rear fillet molding rear with a double-sided tape remover, after removing rear fillet molding rear.

  • Degrease rear fillet molding rear mounting surface of rear fender panel.

  • Paint grain or dust on mounting surface of rear fillet molding rear may spoil exterior appearance if it remains. Clean the mounting surface and check that no paint grain or dust remains, before starting the operation.

  • When installing rear fillet molding rear, visually check the clips, then replace it with new parts if they are damaged.

  • When installing rear fillet molding rear, check that clips are securely fitted in holes, and then press it in.

  • Never wash the vehicle within 24 hours after installing so as to keep adhesive.

    Other materials

    Automatic operation
    The electronic parking brake in the Nissan Armada will automatically release when the vehicle begins to move, provided the following conditions are met: The engine is running. The transmission is in D (Drive) or R (Reverse). The driver’s door is closed. In some situations, the parking ...

    Body Construction
    Body Construction Outer side body Outer front pillar reinforcement Upper front pillar reinforcement Upper inner front pillar Side dash reinforcement (Upper) Upper side dash Weld nut Upper hinge plate Hoodledge reinforcement Upper front pillar hinge brace Side dash ...

    Precautions
    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger fo ...